LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2016 >> G550 >> Repair and Diagnosis >> Suspension >> Rear Suspension >> Rear Axle - 463 Chassis >> Testing & Repair >> Check And Adjust Concentricity Of Drive Flange >> Check And Adjust Concentricity Of Drive Flange - AR35.30-P-4671F

Check And Adjust Concentricity Of Drive Flange - AR35.30-P-4671F

Model 460 

Model 461 (except 461. 331) 

Model 463 (except 463.270/271) 

up to model year 2013 

MODIFICATION NOTES

26.02.2020 Document completely revised.
G13668290Courtesy of MERCEDES-BENZ USA
  Risk of death  caused by vehicle slipping or toppling off of the lifting platform. Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. AS00.00-Z-0010-01A
CAUTION Risk of injury  to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil Wear protective gloves, protective clothing and safety glasses. Do not pour transmission oil into beverage bottles. AS00.40-Z-0001-01A
CAUTION Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. AS00.00-Z-0017-01A
  Notes on avoiding damage through contamination and foreign objects   AH00.00-P-5000-01A
  Notes on self-locking nuts and bolts   AH00.00-N-0001-01A
REMOVING Remove     
1 Lift vehicle with vehicle lift.   AR00.60-P-1006A
2 Detach propeller shaft from drive flange (1) and fasten to frame at side. Model 460 Model 461 (except 461. 331) Model 463 (except 463.270/271) up to model year 2013  
    Model 461. 392 AR41.10-P-0050SW
    Model 461 (except 461. 331/392) Model 463 (except 463.270/271) up to model year 2013 except code 979 (Special protection MB Guard) AR41.10-P-0050GX
INSPECT Check     
3
REFER TO SHOP-MADE TOOLS
Carry out concentricity measurement on drive flange (1).   AR35.30-P-4671-02A 
  Base plate for measuring tripod   WF58.50-P-3330-04A
    Total concentricity deviation of flange *BE35.30-P-1004-01A 
    SPECIAL TOOL Dial indicator holder Fig 5
    SPECIAL TOOL Dial gauge Fig 4
    SPECIAL TOOL Measuring flange Fig 1
    If problems exist,  
     
    adjust concentricity of drive flange. AR35.30-P-4671-01G 
    SPECIAL TOOL Puller Fig 3
    SPECIAL TOOL Retainer wrench Fig 2
INSTALLING Install     
4 Attach propeller shaft to drive flange (1). Model 460 Model 461 (except 461. 331) Model 463 (except 463.270/271) up to model year 2013  
    Model 461. 392 AR41.10-P-0050SW
    Model 461 (except 461. 331/392) Model 463 (except 463.270/271) up to model year 2013 except code 979 (Special protection MB Guard) AR41.10-P-0050GX
5 Lower vehicle with vehicle lift.   AR00.60-P-1006A
CHECK VALUES FOR REAR AXLE DRIVE

Number Designation Model 460, 461, 463
BE35.30-P-1004-01A Total concentricity deviation of flange mm ≤ 0, 07
Fig 1: Identifying Measuring Flange (460 589 01 23 00)
G13668291Courtesy of MERCEDES-BENZ USA
Fig 2: Identifying Retainer Wrench (460 589 01 31 00)
G13668292Courtesy of MERCEDES-BENZ USA
Fig 3: Identifying Puller (460 589 02 33 00)
G13668293Courtesy of MERCEDES-BENZ USA
Fig 4: Identifying Dial Gauge (001 589 53 21 00)
G13668294Courtesy of MERCEDES-BENZ USA
Fig 5: Identifying Dial Indicator Holder (363 589 02 21 00)
G13668295Courtesy of MERCEDES-BENZ USA