LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2016 >> E400 Base, 2D Convertible >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Electrical System - Body - 207 Chassis - 1 Of 4 >> Basic Knowledge >> Media interface function >> Media interface function - GF82.60-P-2020CA

Media interface function - GF82.60-P-2020CA

MODEL 207 with CODE (518) Media interface up to model year 2013/YoM 12 

Function requirements for media interface, general 

Media interface, general 

With the media interface function, it is possible to connect the following portable terminals to the audio equipment via a media interface adapter cable, the media interface electrical connector (X18/70), the media interface control unit (N125/1) and Media Oriented System Transport (MOST).

IMPORTANT The AUX jack electrical connector (X39/45) (up to 31.5.2011 in the glove compartment and as of 1.6.2011 in the stowage compartment (telephone compartment) under the center armrest) is discontinued.

IMPORTANT The media interface electrical connector and the media interface adapter cable are located up to 31.5.2011 in the glove compartment and as of 1.6.2011 in the stowage compartment (telephone compartment) under the center armrest.

The following devices can be connected:

AUX devices without an operating facility are connected to the AUX connection.

"iPods" can be connected to the "iPod" connector.

USB devices are connected to the USB connector.

Media Transfer Protocol (Class 2) devices are connected to the USB connector and the AUX connector.

IMPORTANT In vehicles as of 1.7.2011 with code (512) COMAND APS with DVD changer or code (526) COMAND with single DVD drive (without navigation) or code (527) COMAND APS with single DVD drive (with navigation) or code (528) COMAND incl. DVD changer)

If you try to connect a USB memory stick using an adapter cable to the media interface electrical connection, the following message appears on the Audio/COMAND display (A40/8) "Note: Please connect the device to the other USB port". The USB electrical connector (X115) for connecting USB memory sticks is also located in the stowage compartment (telephone compartment) under the center armrest.

Menu navigation and graphic representation of the menu navigation are shown on the Audio/COMAND display and are dependent on the specific portable terminal connected.

Operation of the listed portable terminals (except AUX devices) is conducted using one of the following controls:

IMPORTANT As of 1.6.2010: With the audio source "Aux" (via media interface adapter cable), the selections "Standard" and "Boost" are possible in the "Volume" menu. The input level can be increased by selecting "Boost".

Function sequence for media interface 

The media interface control unit is supplied with voltage through 2 direct lines (circuit 31 and circuit 30). If an "iPod" or a USB device is connected, it is recognized by the media interface control unit via the following route:

The media interface control unit then sends a signal to the audio equipment, which then switches to the connected source. The audio signals and data from the connected portable device are transferred to the audio equipment via the following route:

IMPORTANT If the audio equipment is switched off, it is not activated when a portable terminal is connected through the media interface system.

In vehicles with code (512) COMAND APS with DVD changer or code (526) COMAND with single DVD drive (without navigation) or code (527) COMAND APS with single DVD drive (with navigation) or code (528) COMAND incl. DVD changer without code (218) Reversing camera and in vehicles with code (498) Japan version without code (610) Night View Assist, video signals and data can also be processed and displayed.

The media interface electrical connection routes the video signals and data over a direct line to the audio equipment. The video signals and data are then processed internally and transmitted to the Audio/COMAND display via a low voltage differential signal (LVDS) line.

The user can now display the audio data or video data on the Audio/COMAND display by selecting the "Media Interface" menu item as well as the specific submenu item (e.g. "Playlists", "Artists", "Albums", "Genres" or "Audio books").

The "Media interface" menu item and the respective submenu item can be selected using the following controls:

The control signals of the left multifunction steering wheel button group and right multifunction steering wheel button group are forwarded to the audio equipment in the following way:

The control signals of the Audio/COMAND control panel are forwarded to the "audio equipment" via the telematics CAN (CAN A).

The control signals from the buttons on the "Audio equipment" are processed internally.

Following evaluation of the control signals in the audio equipment, they are forwarded by the audio equipment to the connected portable end device via the following route:

The connected portable end device evaluates the control signals and sends the corresponding audio signals and data to the audio equipment via the following route:

On vehicles with code (810) Sound system, the audio equipment forwards audio signals over MOST to the sound system amplifier control unit (N40/3). The sound system amplifier control unit emits the audio signals at the speaker system.

On vehicles without code (810) Sound system, the audio signals are emitted by the audio equipment over the following speakers via direct lines:

IMPORTANT More detailed information on the speaker system is available in the "Speaker output function" information.

REFER TO SYSTEM WIRING DIAGRAMS Electrical function diagram for media interface, function   PE82.85-P-2059-97EAA
  Overview of system components, telematics   GF82.85-P-9999CA
scientia non olet · About LEMON Manuals