Retrofit illuminated door sill molding - AN82.20-P-0001GQ

MODEL 166.0 without CODE 876 (Interior lighting package) 

Fig 1: Identifying Retrofit Illuminated Door Sill Molding Components

Courtesy of MERCEDES-BENZ USA

	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove
1	Move front seats toward front
2	Remove rear seat cushion
		MODEL 166.0 without CODE 876 (Interior lighting package) 60% rear seat cushion	AR91.12-P-1020GQ
		MODEL 166.0 without CODE 876 (Interior lighting package) 40% rear seat cushion	AR91.12-P-1020GQA
3	Remove rear seat backrest
		MODEL 166.0 without CODE 876 (Interior lighting package) 60% rear seat	AR91.12-P-1620GQ
		MODEL 166.0 without CODE 876 (Interior lighting package) 40% rear seat	AR91.12-P-1620GQA
4	Remove inner door sills at front and rear entrances
			AR68.30-P-4100GQ
5	Remove outer door sills at front entrances
			AR88.80-P-1001GQ
		The front outer door sills are no longer required.
6	Detach edge guard (1) in area of front left and right entrance
7	Remove rear control unit
			AR54.21-P-2009GQ
		Check in the EPC whether the rear control unit installed according to the vehicle equipment can be used for retrofitting the illuminated door sill moldings. If necessary, the rear control unit is to be removed and replaced with one that is compatible with the illuminated door sill moldings. If replacement of the rear control unit is not necessary, just expose this until the electrical connectors are accessible.
	Install
8	Retrofit left front illuminated door sill molding (E17/47) and right front illuminated door sill molding (E17/48)		AN82.20-P-0001-04GQ
		Cleaner	*BR00.45-Z-1025-04A
9	Retrofit wiring harness for left front illuminated door sill molding (E17/47) and right front illuminated door sill molding (E17/48)		AN82.20-P-0001-03GQ
		New passenger car wiring harness repair kit	Fig 2
		Wiring harness repair kit, basic	Fig 3
10	Install remaining parts
11	Enter special equipment in online vehicle data card via vehicle documentation system (VeDoc)	Add:  CODE 876 (Ambiance illumination)
12	Document retrofitted equipment through VeDoc	Attach note "Illuminated door sill moldings retrofitted as per AN82.20-P-0001GQ " under field organization texts to design group 82.
13	Connect Star Diagnosis and select vehicle via the vehicle identification number (VIN)
			AD00.00-P-2000-04A
14	Perform variant coding with XENTRY using the software calibration number (SCN)
15	Disconnect STAR DIAGNOSIS
			AD00.00-P-2000-04A
	Check
16	Check function of left front illuminated door sill molding (E17/47) and right front illuminated door sill molding (E17/48)	By opening the front doors, the left front illuminated door sill molding (E17/47) and the right front illuminated door sill molding (E17/48) are activated.
17	Remove protective foil at left front illuminated door sill molding (E17/47) and right front illuminated door sill molding (E17/48)

Fig 2: Identifying New Passenger Car Wiring Harness (220 589 04 99 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Wiring Harness Repair Kit, Basic Repair Kit (000 589 13 99 00)

Courtesy of MERCEDES-BENZ USA

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71

PARTS ORDERING NOTE

Part no.	Designation	Quantity
KG 99 (see EPC)	Illuminated door sill moldings	1
Handelsublich	Brown line 0.75 mm2	4000 mm
Handelsublich	Round cable lug 6 mm	2