Remove/install wheels, rotate if necessary - AP40.10-P-4050HA

MODEL 217, 222 

Left illustration 

Fig 1: Wheel Bolts Tightening Sequence

Courtesy of MERCEDES-BENZ USA

Right figure 

Fig 2: Interchanging Wheel And Tire Assemblies

Courtesy of MERCEDES-BENZ USA

	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Information on tires/rims		AH40.10-P-9411-01A
	Notes on handling, transport and storage of ceramic brake disks	Model 217, 222 with code B07 (Ceramic brake system)	AH42.10-P-9406-13A
	Notes on handling, transport and storage of composite brake disks		AH42.10-P-9406-12LF
	Preparatory activity
1	Lift vehicle on vehicle lift		AR00.60-P-1000LF
	Remove
2	Remove hubcaps	Vehicle with hubcaps.
3	Unfasten wheel bolts and wheels using wheel lift	Complete wheels may only be removed using a wheel lift. The brake disks and complete wheels can otherwise be damaged.
	Check
4	Check tires for signs of damage and make sure that they are in good condition	If complaint present ↓ Rectify problem subject to separate repair order.	AP40.10-P-4051EW
5.1	Check manufacture date of tires on front and rear axle	Model 222 with code Z07 (Top protection) Countries with hot climate. Countries with temperate climate. If the manufacture date is older than 6 years or if the driven distance is higher than 15, 000 km in countries with a temperate climate, when the load applied to each tire does not exceed a maximum of half the load capacity per axle or maximum 100 % of the load index on the tire. ↓ Subject to a separate repair order, replace the tires for safety reasons.
		Overview of recommended tires Model 222 (except 222.077/177/178/179) with code Z07 (Top protection)	GF40.10-P-1008YE
5.2	Check manufacture date of tires on front and rear axle	Model 222 with code Z07 (Top protection) If the manufacture date is older than 6 years or if the driven distance is higher than 10, 000 km in countries with a hot climate, when the load applied to each tire does not exceed a maximum of half the load capacity per axle or maximum 100 % of the load index on the tire. ↓ Subject to a separate repair order, replace the tires for safety reasons.
		Overview of recommended tires Model 222 (except 222.077/177/178/179) with code Z07 (Top protection)	GF40.10-P-1008YE
	Install
6	Clean and check wheel bolt connection components, then protect against corrosion	Before mounting a wheel-and-tire assembly all  the operation steps listed in the linked description must be conducted carefully. The complete wheel can otherwise work its way loose from the vehicle.	AP40.10-P-4050-01A
		Paste, hot lubrication 1 kg, DBL 6879.20	*BR00.45-Z-1005-06A
7	Change round wheel-and-tire assemblies on front and rear axles	If necessary, subject to separate repair order and only for vehicle without mixed tires. The running direction of the complete wheels must be retained. Otherwise handling characteristics and handling comfort may be impaired and tire wear increased.
8	Mount wheels using wheel lift and tighten wheel bolts	Complete wheels may only be removed using a wheel lift. The brake disks and complete wheels can otherwise be damaged. The tightening sequence (1 to 5) and tightening torque must be observed. Otherwise, the complete wheel may be damaged or work its way loose from the vehicle. Model 217, 222 Wheel bolt	*BA40.10-P-1001-01A
9	Lower vehicle		AR00.60-P-1000LF
10	Correct tire pressure of front and rear axle tires	In the event of unusual tire pressure loss ↓ Determine and rectify cause, subject to separate repair order.	AP40.15-P-4061A
11	Mount hubcaps	Vehicle with hubcaps. Hubcaps must be correctly positioned relative to the valves and securely seated. Otherwise the valve will be damaged or the hubcaps will be lost.
12.1	Activate the tire pressure monitoring system	Model 217 with code 475 (Tire pressure monitoring system) Model 222 with code 475 (Tire pressure monitoring system) Only for wheel-and-tire assembly change, tire replacement or a change in tire pressure.
			AR54.30-P-1001-01LC
12.2	Activate tire pressure loss warning	Model 217 except code 475 (Tire pressure monitoring system) Model 222 except code 475 (Tire pressure monitoring system) Only for wheel-and-tire assembly change, tire replacement or a change in tire pressure.

WHEELS

Number	Designation		Model 217	Model 222 except code Z07 (Top protection)
BA40.10-P-1001-01A	Wheel bolt	Nm	150	150

WHEELS

Number	Designation		Model 222 with code Z07 (Top protection)
BA40.10-P-1001-01A	Wheel bolt	Nm	180

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1005-06A	Paste, hot lubrication 1 kg, DBL 6879.20	A 000 989 76 51