Rear rubber bushing, rear axle mount - Removal and installation - AR35.10-P-0042SX

MODEL 221 except CODE (Z07) Top protection 

MODEL 216 

Fig 1: Identifying Rubber Bushing, Bolt, Rear Axle Carrier And Rear Axle Center Assembly

Courtesy of MERCEDES-BENZ USA

Fig 2: Removing/Installing Rear Rubber Bushing (1 Of 2)

Courtesy of MERCEDES-BENZ USA

Fig 3: Removing/Installing Rear Rubber Bushing (2 Of 2)

Courtesy of MERCEDES-BENZ USA

MODIFICATION NOTES

20.1.06

Liquid lubricant (naphtolen H) replaced by rubber assembly fluid

Step 12

	Removing
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	While working on the rear axle care must be taken to ensure that the surface of all aluminum components do not get any scratches, cracks and notches. Otherwise the service life of the parts will be affected
	Always replace rear rubber mounts (1) in pairs
	The following tools are required from the extraction and insertion tools: thrust piece (01)221 589 00 43 01, thrust piece (03)221 589 00 43 03, support (02)221 589 00 43 02, support (04)221 589 00 43 04, spindle (05) 221 589 00 43 05 and sleeve (011)221 589 00 43 11		*221589004300
1	Secure vehicle on lifting platform		AR00.60-P-0100SX
2	Remove rear wheels. Remove/install wheels		AP40.10-P-4050SX
3	Remove exhaust system as of flange connection	Engine 156, 272, 273, 275	AR49.10-P-7100SX
		Engine 642, 629	AR49.10-P-7100SXI
4	Detach propeller shaft from rear axle center assembly (50)		AR41.10-P-0050-03SX
5	Prop up rear axle carrier (4) on rear axle center assembly (50) using transmission jack and transmission platform	Transmission platform Transmission jack
6	Mark the installation position of the respective rubber mount (1) at cutout (arrow)
7	Remove bolts (1 s) of rubber mounts (1)
8	Lower the rear axle carrier (4)
9	Attach thrust piece (01), support (02), spindle (05) and sleeve (011) with hollow cylinder (015) and retaining belt (012) to rubber mount (1) of rear axle carrier (4)	The retaining belt must be routed behind the thrust piece in order to prevent the hollow cylinder falling down when the rubber mount is pressed out.
			652589003322
			001589016300
10	Connect hand pump (014) using hydraulic hose (013) on hollow cylinder (015)		*652589003321
			652589003323
			652589003322
11	Press rubber mount (1) out of rear axle carrier (4)	When pressing out the rubber mount the hollow cylinder (015) is supported in the retaining belt (012). Keep your distance!
	Install
12	Coat new rubber mounts (1) with rubber assembly fluid		*BR00.45-Z-1010-06A
13	Attach thrust piece (03), support (04), spindle (05) and sleeve (011) with hollow cylinder (015) and retaining belt (012) to the rubber mount (1) of the rear axle carrier (4)		*652589003322
			*001589016300
14	Press rubber mount (1) into rear axle carrier (4)
15	Raise rear axle carrier (4).
16	Screw in bolts (1s) of rubber mounts (1)		*BA35.10-P-1002-01M
17	Mount propeller shaft onto rear axle center assembly (50)		AR41.10-P-0050-04SX
18	Install exhaust system as of flange connection	Engine 156, 272, 273, 275	AR49.10-P-7100SX
		Engine 642, 629	AR49.10-P-7100SXI
19	Fit rear wheels
	Remove/install wheels		AP40.10-P-4050SX
20	Remove lifting platform safety device		AR00.60-P-0100SX

REAR AXLE CARRIER

Number	Designation			Model 221 except 221.176/179 with rear axle differential 240V	Model 221.176/179 with rear axle differential 240V
BA35.10-P-1002-01M	Self-locking bolt, rear axle carrier rear rubber mount to frame floor	Stage 1	Nm	80	80
		Stage 2	∠°	90	90

REAR AXLE CARRIER

Number	Designation			Model 216
BA35.10-P-1002-01M	Self-locking bolt, rear axle carrier rear rubber mount to frame floor	Stage 1	Nm	80
		Stage 2	∠°	90

Fig 4: Identifying Extraction And Insertion Tool (221 589 00 43 00)

Courtesy of MERCEDES-BENZ USA

Fig 5: Identifying Hand Pump (652 589 00 33 21)

Courtesy of MERCEDES-BENZ USA

Fig 6: Identifying Hollow Cylinder (652 589 00 33 22)

Courtesy of MERCEDES-BENZ USA

Fig 7: Identifying Hydraulic Hose (Complete) (652 589 00 33 23)

Courtesy of MERCEDES-BENZ USA

Fig 8: Identifying Retaining Belt (001 589 01 63 00)

Courtesy of MERCEDES-BENZ USA

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1010-06A	Lubricant, rubber assembly 1 l	A 000 989 03 67