Retrofit AMG light alloy wheels - AZ40.10-P-0003TB

MODEL 211 except CODE (Z04) Light armoring except CODE (Z06) B6 armoring except CODE (Z07) Top protection except 4-MATIC

AMG spoked wheel Styling III

8.5Jx19 H2 ET 34 (B6 603 1226)

9.5Jx19 H2 ET 31 (B6 603 1227)

For possible tires see Technical Inspection Association (TUV) approval certificate.

Fig 1: Identifying AMG Spoked Wheel Styling III

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

AMG spoked wheel Styling III

VA 8.5J8x19 EH2 ET 30 (B6 603 1232)

HA 9.5Jx19 EH2 ET 31 (B6 603 1233)

For possible tires see Technical Inspection Association (TUV) approval certificate.

Fig 2: Identifying AMG Spoked Wheel Styling III

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

AMG spoked wheel Styling IV multiple-piece

8.5Jx19 EH2 ET 30 (B6 603 1360)

9.5Jx19 EH2 ET 31 (B6 603 1361)

For possible tires see Technical Inspection Association (TUV) approval certificate.

Fig 3: Identifying AMG Spoked Wheel Styling IV Multiple-Piece

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

	A prerequisite for the use of the wheels/tires combination is the complete implementation of the scopes described	In the Federal Republic of Germany, installation approval is required after conversion from an officially recognized expert or inspector from a motor vehicle inspection center or an inspection engineer from an officially recognized supervisory organization.
	Tire approval certification	Model 211.004 /006 /016 /020 /022 /023/026 /028 /029 /042 /054 /056 /061 /065 / 070 /076 /206 /216 /220 /222 /223 /226 / 242 /254 /256 /261 /265 /270 /276. * For Germany only	OF40.10-P-1000-01RC
	Wheel/tire combination/tire make / using snow chains		AZ40.10-P-0001-01K
	Tire inflation pressure	See TUV certificate.
	Remove
1	Removing standard wheels		AZ40.10-P-0001-03B
2.1	Replace standard front stop buffer	Only on vehicles without MB sport suspension code 486 or Airmatic (semi-active pneumatic suspension) code 489a ↓:
	Replace standard front stop buffer	Dismantle and assemble suspension strut Model 211.0, 211.2	AR32.25-P-1018TS
3	Body retrofitting work at front fender		AZ40.10-P-0001-04T
4	Reworking body at rear wheel houses		AZ40.10-P-0001-10T
	Install
5	Fit special wheels	On Styling III special wheels use only M14x1.5x45 spherical collar bolts On Styling IV multi-part special wheels use only M14x1.5x27 spherical collar bolts (standard).	AZ40.10-P-0001-08C

PARTS ORDERING NOTES

Part no.	Designation	Quantity
B6 603 12 26	Light alloy disk wheel 8.5 Jx19 H2 ET 34 (Styling III) with rubber valve and wheel trim cover and wheel bolts	2
B6 603 12 27	Light alloy disk wheel 9.5 Jx19 H2 ET 31 (Styling III) with rubber valve and wheel trim cover and wheel bolts	2
A220 400 01 25 9715	Wheel trim cover	as required
A000 400 02 13	Rubber valve	as required
A000 990 09 07	Wheel bolt M14x1.5x45 (included in parts kit)	as required
B6 603 13 60	Light alloy disk wheel 8.5 Jx19 EH2 ET 30 (Styling IV) with rubber valve and wheel trim cover	2
B6 603 13 61	Light alloy disk wheel 9.5 Jx19 EH2 ET 31 (Styling IV) with rubber valve and wheel trim cover	2
A220 400 01 25 9709	Wheel trim cover	as required
A000 400 02 13	Rubber valve	as required
A211 401 03 70	Wheel bolt M14x1,5x27 (standard, not included in parts kit)	as required
B6 603 12 32	Light alloy disk wheel 8.5 Jx19 H2 ET 30 (Styling III)	2
B6 603 12 33	Light alloy disk wheel 9.5 Jx19 H2 ET 31 (Styling III)	2
A220 400 01 25 9715	Wheel trim cover (not included in parts kit)
A211 323 02 44	Pressure stop damper (not included in parts kit)	as required