Checking alignment of spring link, camber strut, tension arm, torque strut and track rod on rear axle - AR40.30-P-0420I
MODELS 220, 215
Fig 1: Identifying Alignment Of Spring Link, Camber Strut, Tension Arm, Torque Strut And Track Rod On Rear Axle - Models 220, 215
| Before measuring, perform visual inspection | Check individual parts for damage, corrosion and wear | ||
| Measuring camber strut | |||
| 1 | Remove, install camber strut (2) | AR35.20-P-0110I | |
| 2 | Install/remove plug gauges (041b) | ||
| Plug gauge for rear wheel location | WF58.50-P-4030-01A | ||
| 3 | Measure dimension "L1" on both sides | *WH58.30-Z-1006-12A *BE40.30-P-1001-03A |
|
| Measuring tension arm | |||
| 4 | Remove, install tension arm (3) | AR35.20-P-0111I | |
| 5 | Install/remove plug gauges (041b) | ||
| Plug gauge for rear wheel location | WF58.50-P-4030-01A | ||
| 6 | Measure dimension "L4" on both sides | *WH58.30-Z-1006-12A *BE40.30-P-1001-03A |
|
| Measuring track rod | |||
| 7 | Remove, install track rod (4) | AR35.20-P-0112I | |
| 8 | Install/remove plug gauge (041d) | Mark center point of track rod end. | |
| Plug gauge for rear wheel location | WF58.50-P-4030-01A | ||
| 9 | Measure dimension "L3" | *WH58.30-Z-1006-12A *BE40.30-P-1001-03A |
|
| Measuring torque strut | |||
| 10 | Remove, install torque strut (5) | AR35.20-P-0113I | |
| 11 | Install/remove plug gauges (041b) | ||
| Plug gauge for rear wheel location | WF58.50-P-4030-01A | ||
| 12 | Measure dimension "L2" on both sides | Figure *BE40.30-P-1001-03A |
|
| Measuring spring link | |||
| 13 | Remove, install spring link (6) | AR35.20-P-0114I | |
| with Code 487a Active Body Control (ABC). | AR35.20-P-0114N | ||
| 14 | Install / remove plug gauges (041e, 041f) | ||
| Plug gauge for rear wheel location | WF58.50-P-4030-01A | ||
| 15 | Measure dimension "L5" on both sides | Figure *BE40.30-P-1001-03A |
TEST VALUES FOR TORQUE STRUT/TENSION ARM/CAMBER STRUT, SPRING LINK, TRACK ROD ON REAR AXLE
| Number | Designation | Model 215 | Model 220 | ||
|---|---|---|---|---|---|
| BE40.30-P-1001-03A | Dimension | Camber strut "L1" | mm | 322 (± 0.5) | 322 (± 0.5) |
| Torque strut "L2" | mm | 432 (± 0.5) | 432 (± 0.5) | ||
| Track rod "L3" | mm | 269.3 (± 0.5) | 269.3 (± 0.5) | ||
| Tension arm "L4" | mm | 395 (± 0.3) | 395 (± 0.3) | ||
| Spring link "L5" | mm | 492 (± 0.5) | 492 (± 0.5) | ||
| See figure | - | - | |||
COMMERCIALLY AVAILABLE TOOLS
| Number | Designation |
|---|---|
| WH58.30-Z-1006-12A | Caliper gauge |