Remove/install fuse and relay box in engine compartment, left front - AR54.15-P-1257T
MODEL 211.0 /2 /6 up to 31.5.06
Illustrated on model 211.070
Shown on model 211.070
MODIFICATION NOTES
| 25.3.02 | Value changed from 110 Nm to 130 Nm | Value changed in row for model 211 | *BA40.10-P-1001-01A |
| Remove/install | |||
|---|---|---|---|
| 1 | Remove and install SAM control unit with fuse and relay box, left front. | AR54.21-P-1260T | |
| 2 | Remove electronic stability program control unit (ESP) | AR42.45-P-0820T | |
| 3.1 | Remove injection system control unit | Model 211.004/006/016/023/026/061/065/070/076/080/082/083/206/216/223/226/261/265/270/276/280/282/283/606/616 | AR07.08-P-7008T |
| Model 211.028 | AR07.08-P-7008TD | ||
| Type 211.029 | AR07.08-P-7008TJ | ||
| Models 211.020/ / 022/084/ 089/220/ 222/284/289/620 | AR07.08-P-7008TI | ||
| 4 | Remove cable duct seal (2) | ||
| 5 | Lift right wiring harness (3), disconnect electrical connector (6) and move right wiring harness (3) to one side | ||
| 6 | Lift left wiring harness (5) and move control unit box blower motor (M2/2) out of fuse and relay box (F1) until electrical connector on control unit box blower motor (M2/2) is accessible | ||
| 7 | Unplug electrical connector from control unit box blower motor (M2/2) and remove control unit box blower motor (M2/2) | ||
| 8.1 | Lift AIRmatic relay (K67) together with bracket to unclip it from fuse and relay box (F1) | On vehicles with code (489) Airmatic (semiactive air suspension) | |
| 9 | Remove rear wiring harness (8) from fuse and relay box (F1) and place to one side | ||
| 10 | Lift center wiring harness (4), disconnect electrical connector (9) and place center wiring harness (4) to one side | ||
| 11 | Remove bolts (10) | ||
| 12 | Open tie straps (11) | ||
| 13 | Detach expansion clip from coolant expansion reservoir (12) and place coolant expansion reservoir (12) with lines still connected to one side | ||
| 14 | Disconnect electrical connectors from components at top of engine compartment that are connected to left wiring harness (5) | ||
| 15 | Unclip wiring harness bracket (13) | ||
| 16 | Detach ground leads from left wiring harness (5) at the ground points | ||
| 17 | Expose left wiring harness (5) in top of engine compartment | ||
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| 18 | Lift vehicle on lifting platform. | ||
| 19 | Remove front left road wheel | *BA40.10-P-1001-01A | |
| 20 | Remove front section of fender liner in left front fender | AR88.10-P-1310T | |
| 21.1 | Disconnect front PTS separation point (X26/27) | On vehicles with code (220) Parktronic system PTS | |
| 22 | Remove tie strap (15) | ||
| 23.1 | Separate electrical connector (16) | On vehicles with code (489) Airmatic (semiactive air suspension) | |
| 24 | Unclip plug assembly with bracket (17) from front longitudinal member | ||
| 25 | Separate electrical connectors (18) | ||
| 26.1 | Separate electrical connectors (19) | On vehicles with code (489) Airmatic (semiactive air suspension) | |
| 27 | Lower vehicle on lifting platform | ||
| 28 | Pull left wiring harness (5) up and out of engine compartment | ||
| 29 | Remove fuse and relay box (F1) from engine compartment and guide out all electrical lines | ||
| 30 | Remove fuse and relay box (F1) | ||
| 31 | Install in the reverse order |
| Number | Designation | Model 211 | |
|---|---|---|---|
| BA40.10-P-1001-01A | Wheel bolt | Nm | 130 |