Remove/install oil pan - AR01.45-P-7500L
ENGINE 137.970 in MODELS 215.378, 220.178 /878
ENGINE 275.950 in MODELS 215.376, 220.176
ENGINE 275.980 in MODEL 215.379, 220.179
Shown on engine 137
MODIFICATION NOTES
| 17.5.06 |
Engine oil, filling capacity with and without oil filter |
Engine 275.980 |
*BF18.00-P-1001-01K |
  |
Remove/install |
|
|
 |
|
External Torx set |
Figure |
| 1 |
Remove engine trim panel |
Engine 137.970 |
|
| |
|
Engine 275.950 |
AR01.10-P-2405LA |
| |
|
Engine 275.980 |
AR01.10-P-2405IM |
| 2 |
Attach engine support bracket |
Engine supporting shackle |
*WH58.30-Z-1002-07A |
| 3 |
Raise engine |
Ensure that the engine does not come into contact at the rear with the bodywork, to prevent damage to the bodywork. Do not overtension coolant lines. |
AR01.10-P-7500-03I |
| 4 |
Remove lower engine compartment paneling |
|
AR61.20-P-1105M |
| 5 |
Drain and collect engine oil |
 |
*BA01.45-P-1003-01B |
| |
|
 |
*BF18.00-P-1001-01K |
| 6 |
Remove oil pan bottom section (2) |
Installation:
Observe sealant flow: ↓ |
AR01.45-P-7555L |
|
Notes on application of sealant to oil pan |
Engines 137.970, 275.950 /951 /980 |
AH01.45-P-0001-01A |
| |
|
|
*BA01.45-P-1002-01B |
| |
|
Sealant gun |
Figure |
| |
|
Sealant |
*BR00.45-Z-1013-01A |
| 7 |
Unscrew bolts of front engine mount to front axle carrier |
|
*BA22.10-P-1001-01L |
| 8 |
Lower front axle |
Model 220.878, 215.376 /378 /379 |
|
| |
|
Model 220 except 220.878 |
AR33.10-P-0101M |
| 9.1 |
Remove oil sensor |
Engine 137 |
AR18.40-P-5111L |
| |
|
|
*BA18.40-P-1002-01B |
| 10.1 |
Remove oil pipe of oil dipstick |
Engine 137
Unscrew bolt at cylinder head cover and alternator. |
|
| 11 |
Remove oil pan top section(1) |
Engine 137: Ensure that ground contact (4) is installed.
Engine 137: Remove oil pan top section (1) by pulling forwards in direction of travel - turn crankshaft slightly if necessary and drain engine a little.
Installation:
Replace seal (3). |
|
| |
|
|
*BA01.45-P-1001-01B |
| 12 |
Install in the reverse order |
|
|
OIL PAN
| Number |
Designation |
Engine 137 |
Engines 275, 285 |
| BA01.45-P-1001-01B |
Bolt, oil pan to crankcase |
M6 |
Nm |
8 |
8 |
| M8 |
Nm |
- |
- |
| BA01.45-P-1002-01B |
Self-tapping screw, oil pan to oil pan |
Thread not pretapped |
Nm |
8 |
14 |
| Thread pre-tapped |
Nm |
- |
9 |
| BA01.45-P-1003-01B |
Oil drain screw to oil pan |
M14 |
Nm |
25 |
30 |
ENGINE MOUNTS, ENGINE SUPPORTS
| Number |
Designation |
Engine 112.922/944/972, 113.941/960, 137.970 in model 220 |
Engine 275.950/980 in model 220 |
| BA22.10-P-1001-01L |
Bolt, front engine mounts to front axle carrier |
Nm |
35 |
35 |
ENGINE MOUNTS, ENGINE SUPPORTS
| Number |
Designation |
Engine 137.970 in model 215 |
Engines 275.950/980 in model 215 |
| BA22.10-P-1001-01L |
Bolt, front engine mounts to front axle carrier |
Nm |
35 |
35 |
OIL LEVEL/OIL PRESSURE SENSOR
| Number |
Designation |
Engine 137, 275 |
| BA18.40-P-1002-01B |
Oil level sensor to oil pan top part |
Nm |
8 |
ENGINE LUBRICATION SYSTEM
| Number |
Designation |
Engine 137.970 |
Engine 275.950/953 |
Engine 275.980 |
| BF18.00-P-1001-01K |
Engine oil |
Filling capacity with oil filter |
Liters |
9.0 |
9.0 |
9.0 |
| Filling capacity without oil filter |
Liters |
8.5 |
- |
- |
| Specifications for Operating Fluids |
Sheet |
BB00.40-P-0229-01A |
- |
- |
| Sheet |
BB00.40-P-0229-03A |
BB00.40-P-0229-03A |
BB00.40-P-0229-03A |
| Sheet |
BB00.40-P-0229-05A |
BB00.40-P-0229-05A |
BB00.40-P-0229-05A |
COMMERCIALLY AVAILABLE TOOLS
| Number |
Designation |
| WH58.30-Z-1002-07A |
Engine carrier arm |
REPAIR MATERIALS
| Number |
Designation |
Order number |
| BR00.45-Z-1013-01A |
Sealant |
A 003 989 98 20 |