Retrofit antitheft alarm system (ATA) - AN80.50-P-0001N
MODEL 215 up to 31.8.02
Fig 1: Identifying Retrofit Antitheft Alarm System (ATA) Components (1 Of 6) - Model 215 Up To 31.8.02
Fig 2: Identifying Retrofit Antitheft Alarm System (ATA) Components (2 Of 6) - Model 215 Up To 31.8.02
Fig 3: Tightening Identifying Retrofit Antitheft Alarm System (ATA) Components (3 Of 6) - Model 215 Up To 31.8.02
Fig 4: Identifying Retrofit Antitheft Alarm System (ATA) Components (4 Of 6) - Model 215 Up To 31.8.02
Fig 5: Identifying Retrofit Antitheft Alarm System (ATA) Components (5 Of 6) - Model 215 Up To 31.8.02
Fig 6: Identifying Retrofit Antitheft Alarm System (ATA) Components (6 Of 6) - Model 215 Up To 31.8.02
| Removing | |||
| 1 | Connect no load current retention unit | *WH58.30-Z-1012-09A | |
| 2 | Disconnect battery ground cable | ||
| AR54.10-P-0003I | |||
| 3 | Remove rear seat cushion | ||
| AR91.12-P-1020N | |||
| 4 | Unscrew bolts (7) and nuts (6), remove assembly plate (5) from vehicle floor and fold down toward front. | ||
| 5 | Unscrew nuts (9) and remove rear fuse and relay module (K40/5) from vehicle floor | ||
| 6 | Remove upper control panel control unit. | ||
| AR54.21-P-1262N | |||
| Order for boring hole pattern, form sheet. | OF68.00-P-3000-01A | ||
| 7 | Remove switch group (11) in direction of arrow and disconnect electrical connector (10). | ||
| 8 | Remove front floor covering | ||
| AR68.20-P-2050M | |||
| 9 | Remove finder liner in front fender | ||
| AR88.10-P-1300M | |||
| 10 | Unscrew bolts (14) from left front engine hood catch (12). | ||
| Install | |||
| 11 | Clip ATA engine hood switch (S62) into left front engine hood catch (12). | ||
| 12 | Connect present electrical connector (13) to ATA engine hood switch (S62). | ||
| 13 | Screw bolts (14) into left front engine hood catch (12). | *BA88.40-P-1004-01D | |
| 14 | Retrofit alarm siren | AN80.50-P-0001-02M | |
| 15 | Clip new switch group (11) with TS/IMS switch (N72/1s7) onto upper control panel (N72/1) in direction of arrow and connect to electrical connector (10). | ||
| 16 | Install upper control panel control module (N72/1) | ||
| AR54.21-P-1262N | |||
| 17 | Insert tow-away protection relay (K40/5kR) and fuse 51 (K40/5f51), fuse 77 (F4f77) | ||
| Fuse assignment, as-built configuration | GF54.15-P-1256I | ||
| Relay assignment, as-built configuration | GF54.15-P-1257I | ||
| 18 | Install rear fuse and relay module (K40/5) and fasten wit nuts (9). | ||
| 19 | Loosen line tieout with electrical coupling (8) from wiring harness. | ||
| 20 | Install assembly plate (5) and fasten with bolts (7) and nuts (6). | ||
| 21 | Push ATA inclination sensor (B33) onto assembly plate (5) in direction of arrow and connect electrical coupling (8) to ATA inclination sensor (B33). | ||
| 22 | Retrofitting interior protection | with CODE (551a) Anti-theft alarm system (ATA). | AN80.50-P-0100N |
| 23 | Install remaining parts onto vehicle | ||
| Checking | |||
| 24 | Control unit adaptation for ATA system with STAR diagnosis. |
|
|
| 25 | Check ATA system for proper function | ||
| 26 | When modifying the package, subsequently enter code or designation of corresponding special equipment on vehicle data card and FDOK |
| Number | Designation | Model 215 | |
|---|---|---|---|
| BA88.40-P-1004-01D | Bolt to engine hood catch | Nm | 8 |
COMMERCIALLY AVAILABLE TOOLS
| Number | Designation |
|---|---|
| WH58.30-Z-1012-09A | Quiescent current retention unit |
PARTS ORDERING NOTES
| Part no. | Designation | Quantity |
|---|---|---|
| kg99 | Fender bolt | 3 |
| kg54 | Relays | 1 |
| kg54 | Fuse 5A | 1 |
| kg54 | Fuse 40A | 1 |
| kg54 | Cable tie | 1 |
| kg82 | Anti-towing inclination sensor | 1 |
| kg82 | Hood contact | 1 |
| kg82 | Siren | 1 |
| kg82 | Bracket (for siren) | 1 |
| kg01 | Bolt (siren to bracket) | 1 |
| kg82 | TS/IMS switch according to equipment variant and color | 1 |
| group 68 | Wooden trim strip according to equipment variant and requirements. | 1 |
| group 68 | Center console cover as required | 1 |