 |
Removing |
|
|
| 1 |
Connect no load current retention unit |
|
|
 |
|
|
AR54.10-P-1030-01I |
| 2 |
Disconnect battery ground cable |
|
|
|
|
|
AR54.10-P-0003I |
| 3.1 |
Remove rear seat cushion |
|
|
|
|
|
AR91.12-P-1020MA |
| 3.2 |
Install individual seats |
with code 401, right side only |
|
|
|
|
AR91.12-P-1020M |
| 4.1 |
Remove seat adjustment mechanism on rear seat |
with code 401, right side only |
|
|
|
|
AR91.12-P-1520M |
| 5 |
Unscrew bolts (6) and nuts (7), remove assembly plate (5) from vehicle floor and fold down toward front. |
Do not disconnect electrical wiring plugs. |
|
| 6 |
Unscrew nuts (9) and remove rear fuse and relay module (K40/5) from vehicle floor |
Do not disconnect electrical wiring plugs. |
|
| 7 |
Remove upper control panel control unit (N72/1) |
|
|
|
|
|
AR54.21-P-1262M |
| 8.1 |
Remove switch group (11) in direction of arrow and disconnect electrical connector (10). |
Only with code 220 Parktronic system or code 540 Automatic rear roller blind
Switch group no longer required |
|
| 9 |
Remove left front floor covering. |
|
|
|
|
|
AR68.20-P-2050M |
| 10 |
Remove fender liner in left-hand front fender |
|
|
|
|
|
AR88.10-P-1300M |
| 11 |
Unscrew bolts (14) from engine hood catch (12). |
|
|
 |
Install |
|
|
| 12 |
Clip ATA engine hood switch (S62) into engine hood catch (12). |
ATA engine hood switch (S62) should arrest correctly (see arrows). |
|
| 13 |
Connect electrical connector (13) for ATA engine hood switch (S62) to present plug. |
Fasten connector (13) with cable strap (15). |
|
| 14 |
Screw bolts (14) into engine hood catch. |
 |
*BA88.40-P-1004-01D |
| 15 |
Retrofit bracket (2) with alarm signal horn and additional battery (H3/1). |
|
AN80.50-P-0001-02M |
| 16 |
Clip new switch group (11) with tow-away protection/ATA status indicator inclination sensor switch (S85/3) into upper control panel control unit (N72/1) and connect to electrical connector (10). |
|
|
| 17 |
Install upper control panel control module (N72/1) |
Use new trim strip (4) according to new switch group (11). |
|
|
|
|
AR54.21-P-1262M |
| 18 |
Insert relay for tow-away protection (K40/5kR) and fuses (F4f51, F4f77). |
|
|
 |
Fuse assignment, as-built configuration |
|
GF54.15-P-1256I |
|
Relay assignment, as-built configuration |
|
GF54.15-P-1257I |
| 19 |
Install rear fuse and relay module (K40/5) and screw in nuts (9). |
|
|
| 20 |
Loosen electrical lines (8) from wiring harness. |
|
|
| 21 |
Install assembly plate (5) and screw in bolts (6) and nuts (7). |
|
|
| 22 |
Push ATA inclination sensor (B33) onto assembly plate (5) in direction of arrow and connect line (8) to ATA inclination sensor (B33). |
Note direction of installation. |
|
| 23 |
Retrofitting interior protection |
See installation instructions. |
AN80.50-P-0100M |
| 24 |
Install remaining parts onto vehicle |
Step 10, 9, 4, 3, 2. |
|
| |
Checking |
|
|
| 25 |
Adapt control unit for ATA system with STAR diagnosis. |
Adapt following control units:
|
|
| 26 |
Check ATA system for proper function |
|
|
| 27 |
Amend special equipment code 551 in FDOK |
|
|