Indicating check/warning messages by means of multifunction display function - GF54.30-P-2012B

MODEL 208 as of 1.8.99, 210 as of 1.7.99 

Multifunction display (A1p13) 

Various driver information is displayed in the multifunction display (A1p13).

Apart from displaying total distance and trip distance (basic display) the following system displays can also be selected and shown in the multifunction display (A1p13):

• Audio
• Telephone (special equipment)
• Navigation (special equipment)
• Trip computer

In addition various fault and warning messages  can be overlaid in the multifunction display (A1p13).

Properties of warning and fault messages 

• Priorities  for warning and fault messages The messages have different priorities depending on their importance. There is only one message for each priority level.

(The instrument cluster (A1) works with main and secondary priorities.)

Higher priority messages can force lower priority messages out of the display.

Highest priority messages are, for example:

• "Stop-engine oil level, switch off engine"

• All "Tire defective" messages

Lower priority messages are, for example:

• "Coolant level"
• Audio, navigation and trip computer system displays

• Minimum display time 

The minimum display time is

• 1 second for system menus
• 2 seconds for fault and warning message
• 5 seconds for displays when operating
• 2 seconds for driver information

Increasing the priority 

The priority of a message can be increased at the time it is triggered.

Existing higher priority messages are then forced out of the display for the period of minimum display time for the new message.

• Automatically acknowledgeable  warning and fault messages These messages disappear automatically when the cause of the message is rectified.

  Examples:

  • All "Tire defective" messages
  • "Engine oil temperature too high"
• Manually acknowledgeable  warning and fault messages These messages are erased when the trip odometer reset button (A1s3), system select/voice control pushbutton (S110s3) or pushbutton + and - (specific function setting, volume control) (S111s1) has been pressed.

  As this involves operating the controls, the minimum display time is not maintained.

  Examples:

  • "Bulb failure"
  • "Coolant level"

    There are also messages which are both acknowledgeable automatically and manually.

• Displaying message again after acknowledging 

  There are messages which can only be displayed again after automatic or manual acknowledgment when terminal 15 has been switched off in the meantime:

  • "BAS fault (Brake Assist)"
  • "Coolant level"

  Other messages are also always overlaid again after acknowledgment if their cause has not yet been rectified.

  Example:

  • All "Tire defective" messages
  • "Engine oil temperature too high"
• Warning messages with tone 

  A warning tone of 200 ms duration is also output for most warning messages.

  In addition a warning lamp or indicator lamp  is also actuated for some messages. These lamps come on as long as there is a fault. This also applies when the associated message has been acknowledged.

Once a fault message has been acknowledged the display changes to the previous display screen if there are no other faults.

Storing messages 

Most warning and fault messages are stored in a toroidal-core store in the instrument cluster (A1) after acknowledgment.

Messages which have not been acknowledged are automatically added to the toroidal-core store after terminal 15r is OFF.

Displays of warning and fault messages 

With a few exceptions (e.g. light reminder, key reminder) messages are only displayed when the engine is running.

• Current messages 

  Current messages are overlaid immediately.

• Several current messages 
  • If there are several faults, the messages alternate every 3 seconds.
• Reminder of acknowledged messages 

  If messages were acknowledged while driving, these are displayed again as a reminder when terminal 15r is OFF. In the process, current messages e.g. light reminder fade out this reminder function.

If there are no messages, the basic display appears after terminal 15r is OFF.

• Displaying stored fault messages 

  When the instrument cluster (A1) is activated the stored messages can be paged:

  • Press the system select/voice control pushbutton (S111s3) until the "--FAULTS" display appears in the multifunction display (A1p13).
  • Page the fault messages with the pushbutton + and - (specific function setting, volume control)(S110s1). The messages are displayed in their priority order.

Example 

Four possible messages are illustrated below, together with a brief description.

When there are several faults the sequence of the messages displayed is explained by means of an example  :

• The windshield washer fluid level has dropped below the minimum mark. The message CHECK WINDSHIELD WASHER FLUID LEVEL"  (Fig 1) is displayed in the multifunction display.
• If the coolant level now drops below the minimum mark, the message "CHECK COOLANT/LEVEL"  (Fig 3) is overlaid for the duration of the minimum display time.

  After this the message

  "BATTERY/GENERATOR CHECK - FIND A WORKSHOP"  (Fig 2) is displayed again.

If no other fault occurs, the messages alternate every 3 seconds.

In the example it was assumed that no message had been acknowledged.

• Message: "CHECK WINDSHIELD WASHER FLUID/LEVEL" 

  This message is displayed if the washer fluid for the windshield washer system and headlamp cleaning system drops below the minimum level.

  For more details, see "Voltage coding coolant/windshield washer fluid level, function" document.

  Fig 1: Identifying Check Windshield Washer Fluid Message

  
• Message: BATTERY/GENERATOR CHECK - FIND A WORKSHOP" 

  This message is displayed if the generator (G2) is not working properly but the engine speed is more than 200 rpm. For more details, see "Battery charge and generator indicator, function" document.

  Fig 2: Identifying Check Battery/Generator Message

  
• Message: "CHECK COOLANT/LEVEL" 

  This message is displayed if the coolant has dropped below the minimum level. For more details, see "Voltage coding coolant/windshield washer fluid level, function" document.

  Fig 3: Identifying Check Coolant Level Message

  

  

• Message: "DISPLAY DEFECTIVE/FIND A WORKSHOP 

  This message is displayed if there is a fault in the CAN/engine compartment and as a result the connection to several  control modules is faulty.

  If the connection to only one  control module is faulty the symbol of the particular system  is overlaid at position (2).

  Fig 4: Identifying Display Defective Message

  

  	Instrument cluster (terminal), operating instructions		GF54.30-P-0002-05B
  	Displaying indicator and warning messages via indicator lamps, function		GF54.30-P-2011B
  	Outputting warning messages audibly, function		GF54.30-P-2013B
  	Battery charge and generator indicator	terminal 61	GF54.30-P-3027B
  	Voltage coding coolant/windshield washer fluid level  , function"		GF54.30-P-4001B
  	Liquid crystal display, location/task/function		GF54.30-P-3015A