| 1 |
Remove compact spare tire |
See Owner's Manual. |
|
| 2 |
Fold 3rd row seats to storage position |
Only with code (847). See Owner's Manual. |
|
| 3 |
Remove footwell covers |
See Owner's Manual. |
|
| 4 |
Remove cargo anchor rings |
|
|
| |
Modifying |
|
|
| 5 |
Place template (1) on top of load compartment floor covering and secure with cargo anchor bolts (arrows) |
Turn template over for opposite side. |
|
| |
|
Template |
Fig 5 |
| 6 |
Mark floor covering through center of bolt location (12) for anchor mounting plate (2) |
Only for those positions at which anchor rings will be installed. |
|
| 7 |
Remove template (1) |
|
|
| 8 |
Remove load compartment floor covering |
|
|
 |
|
|
AR68.20-P-4810GH |
| 9 |
Place floor covering faceup on suitable surface |
|
|
| 10 |
Using hole saw, create Ø=57 mm hole for anchor ring assembly |
Only for those positions at which anchor rings will be installed. Secure floor covering appropriately to ensure hole is cut cleanly.
Use mark as a guide for center of hole. |
|
| 11 |
Lower rear axle carrier |
Only Model 163.174 for installation of 2nd row center anchor ring. |
|
|
|
|
AR35.10-P-0020-01GH |
| 12 |
Place template (1) on floor pan and secure with cargo anchor bolts |
|
|
| 13 |
Mark floor pan through center of rivet and bolt locations (12, 13) for anchor mounting plate (2) |
Only for those positions at which anchor rings will be installed. |
|
| 14 |
Remove template (1) |
|
|
| 15 |
At marks, drill Ø=9.5 mm hole (10) for anchor bolt and Ø=4 mm holes (11) for rivets |
Model 163.174: To avoid damaging auxiliary fuel tank, do not drill more than 5mm through floor pan for 2nd row center anchor ring. |
|
| 16 |
Smooth rough edges of holes on underside of floor pan |
|
|
| 17 |
Clean, prime, and paint holes |
|
|
| 18 |
Using an assistant, place mounting plate (2) into position from underneath vehicle and secure with bolt (8) |
Plate should be flush with surface of body. |
|
| 19 |
Rivet plate into position from inside vehicle, then remove bolt (8) |
|
|
| 20 |
Seal underbody at plate location |
Body seam sealant |
*BR00.45-Z-1003-01A |
 |
Installing |
|
|
| 21 |
Install load compartment floor covering |
Do NOT install internal spare on Model 163.174 at this time. |
|
|
|
|
AR68.20-P-4810GH |
| 22 |
Loosely install trim plate (5) to observe fit to floor covering |
Straight edge of plate (5) towards front of vehicle. |
|
| 23 |
Remove trim plate (5) and relieve floor covering so that plate, when installed, is completely flush with floor covering |
Use caution to avoid making hole too large for trim plate to cover hole completely. Square off hole at front. Relieve only down to foam. |
|
| 24 |
Install anchor ring (6) and related components |
Use short spacer (4) on 3rd row rings. Use long spacer (3) on 2nd row outboard rings. Use short bolt (8) and no spacer on 2nd row center ring. |
|
| |
|
Torx bit set |
Figure |
| |
|
 |
*BA68.50-P-1001-02A |
| 25 |
Reinstall rear axle carrier |
Model 163.174 only. |
|
|
|
|
AR35.10-P-0020-01GH |
| 26 |
Reinstall internal spare tire and carrier |
Model 163.174 only. |
|
|
|
|
AR68.30-P-4610GH |
| 27 |
Reinstall compact spare tire |
See Owner's Manual. |
|