LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2024 >> CX-30 Preferred >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Body Panels >> Front Bumper Removal/Installation

Front Bumper Removal/Installation

CAUTION:
  • If the area shown in the figure is repainted, the radar sensor (front side) aiming cannot be performed correctly. If the area shown in the figure needs to be repainted, replace the front bumper.
  • When repainting the front bumper face, do not repaint the radar emitting area shown in the figure, as the radar sensor (front side) aiming may not be performed correctly.
G16375934Courtesy of MAZDA MOTORS CORP.
  1. Affix the protective tape to the position (vehicle body side) shown in the figure to prevent scratches and damage.
    G16375935Courtesy of MAZDA MOTORS CORP.
  2. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .)
  3. Remove the upper face. (See UPPER FACE REMOVAL/INSTALLATION .)
  4. Remove the fasteners.
    G16375936Courtesy of MAZDA MOTORS CORP.
  5. Pull the front over fender in the direction of the arrow shown in the figure and disengage the clips shown in the figure.
    G16375937Courtesy of MAZDA MOTORS CORP.
  6. Remove the screws and fasteners.
    G16375938Courtesy of MAZDA MOTORS CORP.
  7. Remove the bolts and fasteners which can be verified at the position where front under cover No. 1 was pulled back.
    Fig 1: Front Under Cover No. 1, Front Bumper, Fasteners And Bolts With Torque Specification
    G16375939Courtesy of MAZDA MOTORS CORP.
  8. Partially peel back the front deflector.
    G16375940Courtesy of MAZDA MOTORS CORP.
  9. Disconnect the connectors.
  10. Remove the wiring harness clips.
  11. Remove the screws.
    Fig 2: Front Bumper, Fasteners And Screws With Torque Specification
    G16375941Courtesy of MAZDA MOTORS CORP.
  12. Remove the fasteners.
    CAUTION:
    • Carefully remove the front bumper from the front bumper slider No. 1. If the front bumper is removed from the front bumper slider No. 1 with excessive force, the front bumper hooks may be damaged because the front bumper and the front bumper slider No. 1 are engaged firmly.
    • Detach the front bumper hooks from the front bumper slider No. 1 using two people, one person supports the front bumper. If the front bumper hooks are detached from the front bumper without supporting the front bumper, it may fall off and be damaged.
  13. Pull the rear end of the front bumper in the order of the arrows shown in the figure, and detach the front bumper hooks from the front bumper slider No. 1.
    G16375942Courtesy of MAZDA MOTORS CORP.
  14. Pull the front bumper in the direction of the arrows shown in the figure.
    G16375943Courtesy of MAZDA MOTORS CORP.
  15. Disconnect the connectors.
    G16375944Courtesy of MAZDA MOTORS CORP.
  16. Remove the wiring harness clip.
  17. Remove the front bumper.
  18. Install in the reverse order of removal.
  19. Perform the 360° view monitor system aiming. (with 360° view monitor system) (See 360°VIEW MONITOR SYSTEM AIMING .)
  20. Perform the front radar sensor aiming adjustment. (with front radar sensor) (See FRONT RADAR SENSOR AIMING .)
    CAUTION:
    • If there is foreign matter on the front center brand emblem at the position shown in the figure, the aiming cannot be performed correctly. Before performing the aiming, verify that there are no stickers, water, mud, or dirt on the front center brand emblem.
    G16375945Courtesy of MAZDA MOTORS CORP.
  21. Perform the front side radar sensor aiming adjustment. (with front side radar sensor) (See FRONT SIDE/REAR SIDE RADAR SENSOR AIMING .)
CAUTION:
  • If there is foreign matter on the front bumper, the aiming cannot be performed correctly. Before performing the aiming, verify that there are no stickers, water, mud, or dirt on the front bumper.
scientia non olet · About LEMON Manuals