Diagnostic Procedure

DTC P050F:00 (EVP CONTROL UNIT) DIAGNOSTIC PROCEDURE

Step	INSPECTION		Action
1	RECORD SNAPSHOT DATA TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the snapshot data on the repair order.	-	Go to the next Step.
2	VERIFY IF SNAPSHOT DATA IS AFFECTED BY OTHER RELATED DTCs OCCURRING Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT] .) Are following DTCs detected? C101C:00 C101C:18 C101C:71 C101C:72 C101C:73	Yes	Go to the applicable DTC inspection. (See DTC TABLE [EVP CONTROL UNIT] .)
2		No	Go to the next Step.
3	DETERMINE IF EVP CONTROL UNIT POWER SUPPLY CIRCUIT MALFUNCTION Verify the following items with regard to the recorded snapshot data from Step 1. VPS_FBK VPWR Is the snapshot data VPWR value is 8.3-17.4 V when the snapshot data VPS_FBK is On.	Yes	Go to the next Step.
3		No	VPWR PID is below 8.3 V: Perform the DTC U3003:16 procedure. (See DTC U3003:16/U3003:17 [EVP CONTROL UNIT] .) VPWR PID is above 17.4 V: Go to the next Step.
4	DETERMINE WHETHER MALFUNCTION IS PAST OR PRESENT NOTE: When clearing the DTC, the snapshot data is also cleared at the same time. Snapshot data is recorded if it is not recorded in Step 1. Using the M-MDS, clear the DTC from the EVP control unit. (See CLEARING DTC [EVP CONTROL UNIT] .) Switch the ignition ON (engine off). Disconnect the EVP control unit connector. Access the VS1 and VS2 PIDs using the M-MDS. Access the simulation item VPS_FBK using the M-MDS. Verify PIDs VS 1 and VS2 when the electric vacuum pump was operated for 10 s by simulation item VPS FBK. Are VS1 and VS2 PIDs 31.5 kPa {236 mmHg, 9.30 inHg}or more?	Yes	Go to the next Step.
4		No	Go to Step 7.
5	DRIVE VEHICLE THEN VERIFY DTC REPEATABILITY Using the M-MDS, clear the DTC from the EVP control unit. (See CLEARING DTC [EVP CONTROL UNIT] .) Start the engine and drive the vehicle. Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT] .) Is the same Pending DTC present?	Yes	Go to Step 7.
5		No	Go to the next Step.
6	DRIVE VEHICLE THEN VERIFY DTC REPEATABILITY BASED ON SERVICE QUESTIONING RESULTS AND SNAPSHOT DATA Using the M-MDS, clear the DTC from the EVP control unit. (See CLEARING DTC [EVP CONTROL UNIT] .) Drive the vehicle based on the service questions content and snapshot data driving conditions. Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT] .) Is the same Pending DTC present?	Yes	Go to Step 8.
6		No	DTC troubleshooting completed. Explain to the customer that there are no malfunctions with the vehicle based on the contents of the servicing.
7	INSPECT VACUUM LINE Inspect the vacuum line. (See VACUUM LINE INSPECTION .) Is the vacuum line normal?	Yes	Go to the next Step.
7		No	Repair or replace the malfunctioning part, then go to Step 9.
8	INSPECT ELECTRIC VACUUM PUMP Inspect the electric vacuum pump. (See ELECTRIC VACUUM PUMP INSPECTION .) Is the electric vacuum pump normal?	Yes	Go to the next Step.
8		No	Replace the electric vacuum pump, then go to the next Step. (See ELECTRIC VACUUM PUMP REMOVAL/INSTALLATION .)
9	VERIFY DTC TROUBLESHOOTING COMPLETED Using the M-MDS, clear the DTC from the EVP control unit. (See CLEARING DTC [EVP CONTROL UNIT] .) Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT] .) Is the same Pending DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the EVP control unit, then go to the next Step. (See EVP CONTROL UNIT REMOVAL/INSTALLATION .)
9		No	Go to the next Step.
10	VERIFY NO DTC IS PRESENT Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [EVP CONTROL UNIT] .)
10	VERIFY NO DTC IS PRESENT Are any DTCs present?	No	DTC troubleshooting completed.