LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 34 (Exterior Body Panels) >> Front Bumper Removal/Installation (Us)

Front Bumper Removal/Installation (Us)

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.
  1. Affix the protective tape to the position (vehicle body side) shown in the illustration to prevent scratches and damage.
    G13559836Courtesy of MAZDA MOTORS CORP.
  2. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION (US) .)
  3. Remove the upper face. (See UPPER FACE REMOVAL/INSTALLATION .)
  4. Remove the fasteners.
    G13559837Courtesy of MAZDA MOTORS CORP.
  5. Pull the front over fender in the direction of the arrow shown in the illustration and disengage the clips shown in the illustration.
    G13559838Courtesy of MAZDA MOTORS CORP.
  6. Remove the screws and fasteners.
    G13559839Courtesy of MAZDA MOTORS CORP.
  7. Remove the bolts and fasteners which can be verified at the position where front under cover No. 1 was pulled back.
    Fig 1: Front Under Cover No. 1 Bolts With Torque Specification
    G13559840Courtesy of MAZDA MOTORS CORP.
  8. Partially peel back the front deflector.
    G13559841Courtesy of MAZDA MOTORS CORP.
  9. Disconnect the connectors.
  10. Remove the wiring harness clips.
  11. Remove the screws.
    Fig 2: Front Bumper Screws With Torque Specification
    G13559842Courtesy of MAZDA MOTORS CORP.
  12. Remove the fasteners.
    CAUTION:
    • Carefully remove the front bumper from the front bumper slider No. 1. If the front bumper is removed from the front bumper slider No. 1 with excessive force, the front bumper hooks may be damaged because the front bumper and the front bumper slider No. 1 are engaged firmly.
    • Detach the front bumper hooks from the front bumper slider No. 1 using two people, one person supports the front bumper. If the front bumper hooks are detached from the front bumper without supporting the front bumper, it may fall off and be damaged.
  13. Pull the rear end of the front bumper in the order of the arrows shown in the illustration, and detach the front bumper hooks from the front bumper slider No. 1.
    G13559843Courtesy of MAZDA MOTORS CORP.
  14. Pull the front bumper in the direction of the arrows shown in the illustration.
    G13559844Courtesy of MAZDA MOTORS CORP.
  15. Disconnect the connectors.
    G13559845Courtesy of MAZDA MOTORS CORP.
  16. Remove the wiring harness clip.
  17. Remove the front bumper.
  18. Install in the reverse order of removal.
  19. Perform the 360° view monitor system aiming. (with 360° view monitor system) (See 360° VIEW MONITOR SYSTEM AIMING .)
  20. Perform the front radar sensor aiming adjustment. (with front radar sensor) (See FRONT RADAR SENSOR AIMING .)
    CAUTION:
    • If there is foreign matter on the front center brand emblem at the position shown in the illustration, the aiming cannot be performed correctly. Before performing the aiming, verify that there are no stickers, water, mud, or dirt on the front center brand emblem.
    G13559846Courtesy of MAZDA MOTORS CORP.
  21. Perform the front side radar sensor aiming adjustment. (with front side radar sensor) (See FRONT SIDE/REAR SIDE RADAR SENSOR AIMING .)
    CAUTION:
    • If there is foreign matter on the front bumper, the aiming cannot be performed correctly. Before performing the aiming, verify that there are no stickers, water, mud, or dirt on the front bumper.
scientia non olet · About LEMON Manuals