Intention of troubleshooting procedure

Step 1-2
- Perform an emission system parts inspection.
Step 3
- Perform an engine inspection.
Step 4-9
- Perform inspection of HO2S signal related parts.
Step 10-11
- Verify that the primary malfunction is resolved and there are no other malfunctions.

STEP	INSPECTION	RESULTS	ACTION
1	PURPOSE: DETERMINE INTEGRITY OF PURGE SOLENOID VALVE Inspect the purge solenoid valve. (See PURGE SOLENOID VALVE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Replace the purge solenoid valve, then go to Step 10. (See PURGE SOLENOID VALVE REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
1		No	Go to the next step.
2	PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY MALFUNCTION RELATED TO POOR EVAPORATIVE HOSE CONNECTION Verify the connection condition of the evaporative hose (purge solenoid valve side). (See PURGE SOLENOID VALVE REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is the evaporative hose (purge solenoid valve side) connection normal?	Yes	Go to the next step.
2		No	Connect evaporative hose correctly, then go to Step 10. (See PURGE SOLENOID VALVE REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
3	PURPOSE: VERIFY IF MALFUNCTION RELATED TO ENGINE COMPRESSION AFFECTS DIAGNOSTIC RESULTS Inspect the engine compression. (See COMPRESSION INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Are compression pressures within specification?	Yes	Go to the next step.
3		No	Replace or overhaul the engine, then go to Step 10.
4	PURPOSE: INSPECT HO2S CONNECTOR CONDITION Switch the ignition off. Disconnect the HO2S connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 10.
4		No	Go to the next step.
5	PURPOSE: INSPECT INSTALLATION OF HO2S Inspect installation of HO2S. Is the HO2S installed securely?	Yes	Go to the next step.
5		No	Retighten the HO2S, then go to Step 10. (See HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
6	PURPOSE: DETERMINE INTEGRITY OF HO2S Reconnect all disconnected connectors. Inspect the HO2S. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Replace the HO2S, then go to Step 10. (See HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
6		No	Go to the next step.
7	PURPOSE: DETERMINE INTEGRITY OF HO2S HEATER Inspect the HO2S heater. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Replace the HO2S, then go to Step 10. (See HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
7		No	Go to the next step.
8	PURPOSE: INSPECT EXHAUST SYSTEM FOR LEAKAGE Visually inspect for exhaust gas leakage from the exhaust system. Is there any malfunction?	Yes	Repair or replace the malfunctioning part according to the inspection results, then go to Step 10.
8		No	Go to the next step.
9	PURPOSE: VERIFY IF CATALYTIC CONVERTER DAMAGE AFFECTS HO2S SIGNAL Verify if the catalytic converter is damaged. Is there any malfunction?	Yes	Repair or replace the malfunctioning part according to the inspection results, then go to the next step.
9		No	Replace the HO2S, then go to the next step. (See HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
10	PURPOSE: VERIFICATION OF VEHICLE REPAIR COMPLETION Always reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Implement the repeatability verification procedure. (See Repeatability Verification Procedure .) Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Is the PENDING CODE for this DTC present?	Yes	Repeat the inspection from Step 1 of the troubleshooting diagnostic procedure. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to the next step.
10		No	Go to the next step.
11	PURPOSE: VERIFY IF THERE IS ANY OTHER MALFUNCTION Is any other DTC or pending code stored?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
11		No	DTC troubleshooting completed.