| 1 |
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
- Has FREEZE FRAME PID DATA been recorded?
|
Yes |
Go to next step. |
| No |
Record FREEZE FRAME PID DATA on repair order, then go to next step. |
| 2 |
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
- Inspect for related Service Bulletins and/or online repair information availability.
- Is any related repair information available?
|
Yes |
Perform repair or diagnosis according to available repair information.
- If vehicle is not repaired, go to next step.
|
| No |
Go to next step. |
| 3 |
INSPECT TR SWITCH CIRCUIT
- Connect voltmeter to TCM connector.
- Inspect TCM terminal voltage.
- Terminal F
- P position: B+
- N position: B+
- R position and all ranges: 0 V
- Terminal D
- R position: B+
- Other positions and all ranges: 0 V
- Terminal C
- D range: B+
- Other ranges and all positions: 0 V
- Terminal B
- 2 range: B+
- Other ranges and all positions: 0 V
- Terminal A
- 1 range: B+
- Other ranges and all positions: 0 V
- Are any of above terminal voltages are B+
for even a moment while shifting selector lever slowly from P position to 1 range?
|
Yes |
Adjust TR switch, then go to Step 9.
(See TRANSMISSION RANGE (TR) SWITCH ADJUSTMENT
.) |
| No |
Go to next step. |
| 4 |
INSPECT TR SWITCH CONNECTOR FOR POOR CONNECTION
- Turn ignition key to OFF.
- Inspect TR switch connector connection.
- Inspect for poor connection (damaged pulled-out terminals, corrosion, etc.).
- Is connection okay?
|
Yes |
Go to next step. |
| No |
Repair or replace connector and/or terminals, then go to Step 9. |
| 5 |
INSPECT TR SWITCH CIRCUIT
- Connect voltmeter to TCM connector terminal.
- Turn ignition key to ON (engine off).
- Connect harness side connector power line and signal line using jumper wire.
- P position: I and B
- R position: I and F
- N position: I and J
- D range: I and H
- 2 range: I and E
- 1 range: I and G
- Inspect if terminal voltage changes 0 V to B+.
- Does terminal voltage change?
|
Yes |
Go to next step. |
| No |
Go to Step 8. |
| 6 |
INSPECT TR SWITCH FOR OPEN CIRCUIT
- Turn ignition key to OFF.
- Inspect for continuity between TR switch terminals (part-side).
- P position: I and B
- R position: I and F
- N position: I and J
- D range: I and H
- 2 range: I and E
- 1 range: I and G
- Is there continuity between TR switch terminals (part-side)?
(See TRANSMISSION RANGE (TR) SWITCH INSPECTION
.) |
Yes |
Go to next step. |
| No |
Replace TR switch, then go to Step 9.
(See TRANSMISSION RANGE (TR) SWITCH INSPECTION
.) |
| 7 |
INSPECT TR SWITCH POWER CIRCUIT FOR OPEN CIRCUIT
- Turn ignition key to ON (engine off).
- Inspect voltage at TR switch terminal I (vehicle harness-side).
- Is there B+
at TR switch terminal I (vehicle harness-side)?
|
Yes |
Go to Step 9. |
| No |
Inspect main fuse.
- If okay, repair or replace wiring, then go to Step 9.
|
| 8 |
INSPECT TR SWITCH SIGNAL CIRCUIT FOR OPEN CIRCUIT
- Turn ignition key to OFF.
- Inspect for continuity between TR switch terminals (vehicle harness-side) and TCM connector.
- N position: B to F
- R position: F to D
- N position: J to F
- D range: H to C
- 2 range: H to B
- 1 range: H to A
- Is there continuity?
|
Yes |
Go to next step. |
| No |
Repair or replace harness, then go to next step. |
| 9 |
VERIFY TROUBLESHOOTING OF DTC P0706 COMPLETED
- Make sure to reconnect all disconnected connectors.
- Clear DTC from memory using WDS or equivalent.
- Drive vehicle in each range (R, D, 2, and 1) for 25 seconds or more
under following condition.
- Vehicle speed (VSS PID): 60 km/h {37 mph}
- Is pending code present?
|
Yes |
Replace TCM, then go to next step.
(See TRANSMISSION CONTROL MODULE (TCM) REMOVAL/INSTALLATION
.) |
| No |
Go to next step. |
| 10 |
VERIFY AFTER REPAIR PROCEDURE
|
Yes |
Go to applicable DTC inspection. |
| No |
Troubleshooting completed. |