After Repair Procedure

WARNING: This page is about a different car, the 2005 Mazda MX-5 Miata. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION:

After repairing a malfunction, perform this procedure to verify that the malfunction has been corrected.
When this procedure is carried out, be sure to drive the vehicle at lawful speed and pay attention to the other vehicles.

Connect the SSTs (WDS or equivalent) to the DLC-2.
Turn the ignition key to ON (engine off).
Select the clear code function and clear the DTC.
Perform the following DTC inspections to ensure that the DTC has been resolved:
- For P0705
  1. Start the engine.
  2. Drive the vehicle in each range (P, R, N, D, 2, and 1) for 10 seconds or more.
  3. Go to Step 5.
- For P0706
  1. Start the engine.
  2. Drive the vehicle in each range (D, 2, and 1) under the following conditions for 25 seconds or more.
    - Vehicle speed (VSS PID): 60 km/h {37 mph} or above
  3. Go to Step 5.
- For P0715
  1. Start the engine.
  2. Drive the vehicle under the following conditions for 50 seconds or more.
    - Vehicle speed (VSS PID): 20 km/h {12.4 mph}
    - TR switch position: D range
    - Gear position: 1GR
  3. Go to Step 5.
- For P0720
  1. Start the engine.
  2. Drive the vehicle under the following conditions for 85 seconds or more.
    - Vehicle speed (VSS PID): 60 km/h {37 mph} or above
    - TR switch position: D range
    - Gear position: 3GR
  3. Go to Step 5.
- For P0725
  1. Start the engine.
  2. Drive the vehicle under the following condition for 10 seconds or more.
    - Vehicle speed (VSS PID): 60 km/h {37 mph} or above
  3. Go to Step 5.
- For P0741, P0742
  1. Start the engine.
  2. Warm up the engine and transmission.
  3. Drive the vehicle under the following conditions for 24 seconds or more.
    - Vehicle speed (VSS PID): Within 5 km/h {3.1 mph}-100 km/h {62 mph}
    - Engine coolant temperature (ECT PID): 60°C {140°F} or above
    - Engine speed (RPM PID): 600 RPM or above
    - Gear position: 3GR and 4GR
    - TR switch position: D range
    - TCC operation
  4. Go to Step 5.
- For P0751, P0752, P0756, P0757
  1. Start the engine.
  2. Warm up the engine and transmission.
  3. Drive the vehicle and make sure that the gears shift smoothly from 1GR to 4GR under the following conditions.
    - Engine coolant temperature (ECT PID): 60°C {140°F} or above
    - Engine speed (RPM PID): 600 RPM or above
    - Vehicle speed (VSS PID): 5 km/h {3.1 mph} or above
  4. Go to Step 5.
- For P0743, P0753, P0758
  1. Start the engine.
  2. Warm up the engine and transmission.
  3. Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 4GR and TCC is operated.
  4. Go to Step 5.
- For P0222, P0223
  1. Start the engine for 2 seconds or more.
  2. Go to Step 6.
Gradually slow down and stop the vehicle.
Make sure that the repaired DTC does not recur.