DTC Chart: BCM
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B1499:11 | Exterior Lamps Power Supply "A": Circuit Short to Ground | GO to Pinpoint Test G |
| B1499:15 | Exterior Lamps Power Supply "A": Circuit Short to Battery or Open | GO to Pinpoint Test G |
| B149D:11 | Exterior Lamps Power Supply "B": Circuit Short to Ground | GO to Pinpoint Test G |
| B149D:15 | Exterior Lamps Power Supply "B": Circuit Short to Battery or Open | GO to Pinpoint Test G |
| B14E0:11 | Exterior Lamps Power Supply "C": Circuit Short to Ground | GO to Pinpoint Test H |
| B14E0:15 | Exterior Lamps Power Supply "C": Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B14E1:11 | Exterior Lamps Power Supply "D": Circuit Short to Ground | GO to Pinpoint Test H |
| B14E1:15 | Exterior Lamps Power Supply "D": Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B14E2:11 | Exterior Lamps Power Supply "E": Circuit Short to Ground | GO to Pinpoint Test H |
| B14E2:15 | Exterior Lamps Power Supply "E": Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B14E3:11 | Exterior Lamps Power Supply "F": Circuit Short to Ground | GO to Pinpoint Test H |
| B14E3:15 | Exterior Lamps Power Supply "F": Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B14E5:01 | Left Front Enhanced Exterior Lighting System: General Electrical Failure | GO to Pinpoint Test I |
| B14E5:08 | Left Front Enhanced Exterior Lighting System: Bus Signal / Message Failure | GO to Pinpoint Test I |
| B14E5:1C | Left Front Enhanced Exterior Lighting System: Circuit Voltage Out of Range | GO to Pinpoint Test I |
| B14E5:49 | Left Front Enhanced Exterior Lighting System: Internal Electronic Failure | GO to Pinpoint Test I |
| B14E5:55 | Left Front Enhanced Exterior Lighting System: Not Configured | GO to Pinpoint Test I |
| B14E5:61 | Left Front Enhanced Exterior Lighting System: Signal Calculation Failure | GO to Pinpoint Test I |
| B14E7:01 | Right Front Enhanced Exterior Lighting System: General Electrical Failure | GO to Pinpoint Test I |
| B14E7:08 | Right Front Enhanced Exterior Lighting System: Bus Signal / Message Failure | GO to Pinpoint Test I |
| B14E7:1C | Right Front Enhanced Exterior Lighting System: Circuit Voltage Out of Range | GO to Pinpoint Test I |
| B14E7:49 | Right Front Enhanced Exterior Lighting System: Internal Electronic Failure | GO to Pinpoint Test I |
| B14E7:55 | Right Front Enhanced Exterior Lighting System: Not Configured | GO to Pinpoint Test I |
| B14E7:61 | Right Front Enhanced Exterior Lighting System: Signal Calculation Failure | GO to Pinpoint Test I |
| B1533:02 | Headlamp Switch Module: General Signal Failure | GO to Pinpoint Test C |
| B1533:08 | Headlamp Switch Module: Bus Signal / Message | GO to Pinpoint Test C |
| B1533:49 | Headlamp Switch Module: Internal Electronic Failure | GO to Pinpoint Test C |
| B1533:56 | Headlamp Switch Module: Invalid / Incompatible Configuration | GO to Pinpoint Test C |
| B1D00:11 | Left Low Beam: Circuit Short to Ground | GO to Pinpoint Test H |
| B1D00:15 | Left Low Beam: Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B1D01:11 | Right Low Beam: Circuit Short to Ground | GO to Pinpoint Test H |
| B1D01:15 | Right Low Beam: Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B1D02:11 | Left High Beam Circuit: Circuit Short to Ground | GO to Pinpoint Test H |
| B1D02:15 | Left High Beam Circuit: Circuit Short to Battery or Open | GO to Pinpoint Test H |
| B1D03:11 | Right High Beam Circuit: Circuit Short to Ground | GO to Pinpoint Test H |
| B1D03:15 | Right High Beam Circuit: Short to Battery or Open | GO to Pinpoint Test H |
| U1000:00 | Solid State Driver Protection Active -Driver Disabled: No Sub Type Information | The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. For additional information on BCM Field Effect Transistor (FET) protection, REFER to: Module Controlled Functions - System Operation and Component Description . |
| U3000:49 | Control Module: Internal Electronic Failure | The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, INSTALL a new BCM. Refer to the appropriate Removal and Installation procedure in REMOVAL AND INSTALLATION For additional information on BCM Field Effect Transistor (FET) protection, REFER to: Module Controlled Functions - System Operation and Component Description . |
| For other BCM Diagnostic Trouble Codes (DTCs) | - | REFER to: Body Control Module (BCM) . |