E Clutch

WARNING: This page is about a different variant/trim than selected.

Symptom Chart

E clutch

For E clutch operation, REFER to: E Clutch .

E clutch

Condition	Possible Sources	Action
E clutch does not apply	SSE is mechanically stuck off	INSTALL a new solenoid. REFER to: Solenoid .
	E clutch regulator valve stuck off	DISASSEMBLE, CLEAN and INSPECT the regulator valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
	E CL CONTR, hydraulic circuit blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body .
	E clutch hub	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
	E clutch friction plates	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
	E clutch piston seals	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
E clutch always applied	SSE mechanically stuck	INSTALL a new solenoid. REFER to: Solenoid .
	E clutch regulator valve or CL E latch valve stuck on	DISASSEMBLE, CLEAN and INSPECT the regulator valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
	E CL CONTR, hydraulic circuit cross leaks	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body .
	E clutch hub, clutch and planetary carrier, No. 4 ring gear	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
	E clutch friction plates	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
	E clutch piston seals	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
E clutch delayed/soft/slipping apply	Incorrect transmission strategy programmed into PCM/ TCM.	PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .
	Low line pressure	PERFORM line pressure test. REFER to: Special Testing Procedures .
	SSE mechanically sticking	INSTALL a new solenoid. REFER to: Solenoid .
	E clutch regulator valve sticking	DISASSEMBLE, CLEAN and INSPECT the valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
	Gain control valve stuck in default position.	DISASSEMBLE, CLEAN and INSPECT the valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
	E CL CONTR, E CL-FB2 hydraulic circuits blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body .
	E clutch friction plates	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
	E clutch piston seals	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
E clutch harsh apply	Incorrect transmission strategy programmed into PCM/ TCM.	PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .
	High line pressure	PERFORM line pressure test. REFER to: Special Testing Procedures .
	SSE mechanically sticking	INSTALL a new solenoid. REFER to: Solenoid .
	E clutch regulator valve sticking	DISASSEMBLE, CLEAN and INSPECT the valves. If the bore or valve is damaged or worn, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
	Gain control valve stuck in applied position	DISASSEMBLE, CLEAN and INSPECT the valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
	E CL CONTR, E CL-FB2 hydraulic circuit blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body .
	E clutch friction plates	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .
	E clutch piston return springs	INSPECT the components for wear and damage. CLEAN and/or INSTALL new components as necessary. REFER to: Transmission .