LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2013 >> MKS Base, AWD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System >> Diagnosis And Testing >> Airbag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> DTC Charts

DTC Charts

The DTCs can be retrieved from the RCM and the OCSM with a scan tool via the DLC.

NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE: Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to DIAGNOSTIC METHODS for information about these practices.
RESTRAINTS CONTROL MODULE (RCM) DTC CHART

DTC Description Action To Take
B0001:11 Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground GO to PINPOINT TEST A .
B0001:12 Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery GO to PINPOINT TEST A .
B0001:13 Driver Frontal Stage 1 Deployment Control: Circuit Open GO to PINPOINT TEST A .
B0001:1A Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST A .
B0001:2B Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0001:4A Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0002:11 Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground GO to PINPOINT TEST B .
B0002:12 Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery GO to PINPOINT TEST B .
B0002:13 Driver Frontal Stage 2 Deployment Control: Circuit Open GO to PINPOINT TEST B .
B0002:1A Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST B .
B0002:2B Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0002:4A Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0005:11 Collapsible Steering Column Deployment Control: Circuit Short to Ground GO to PINPOINT TEST C .
B0005:12 Collapsible Steering Column Deployment Control: Circuit Short to Battery GO to PINPOINT TEST C .
B0005:13 Collapsible Steering Column Deployment Control: Circuit Open GO to PINPOINT TEST C .
B0005:1A Collapsible Steering Column Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST C .
B0005:2B Collapsible Steering Column Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0005:4A Collapsible Steering Column Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0010:11 Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground GO to PINPOINT TEST D .
B0010:12 Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery GO to PINPOINT TEST D .
B0010:13 Passenger Frontal Stage 1 Deployment Control: Circuit Open GO to PINPOINT TEST D .
B0010:1A Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST D .
B0010:2B Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0010:4A Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0011:11 Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground GO to PINPOINT TEST E .
B0011:12 Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery GO to PINPOINT TEST E .
B0011:13 Passenger Frontal Stage 2 Deployment Control: Circuit Open GO to PINPOINT TEST E .
B0011:1A Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST E .
B0011:2B Passenger Frontal Stage 2 Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0011:4A Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0050:11 Driver Seatbelt Sensor: Circuit Short to Ground GO to PINPOINT TEST F .
B0050:12 Driver Seatbelt Sensor: Circuit Short to Battery GO to PINPOINT TEST F .
B0050:13 Driver Seatbelt Sensor: Circuit Open GO to PINPOINT TEST F .
B0050:1D Driver Seatbelt Sensor: Circuit Current Out of Range GO to PINPOINT TEST F .
B0050:2B Driver Seatbelt Sensor: Signal Cross Coupled GO to PINPOINT TEST Y .
B0050:4A Driver Seatbelt Sensor: Incorrect Component Installed GO to PINPOINT TEST Z .
B0052:11 Passenger Seatbelt Sensor: Circuit Short to Ground GO to PINPOINT TEST G .
B0052:12 Passenger Seatbelt Sensor: Circuit Short to Battery GO to PINPOINT TEST G .
B0052:13 Passenger Seatbelt Sensor: Circuit Open GO to PINPOINT TEST G .
B0052:1D Passenger Seatbelt Sensor: Circuit Current Out of Range GO to PINPOINT TEST G .
B0052:2B Passenger Seatbelt Sensor: Signal Cross Coupled GO to PINPOINT TEST Y .
B0052:4A Passenger Seatbelt Sensor: Incorrect Component Installed GO to PINPOINT TEST Z .
B0070:11 Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground GO to PINPOINT TEST H .
B0070:12 Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery GO to PINPOINT TEST H .
B0070:13 Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Open GO to PINPOINT TEST H .
B0070:1A Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST H .
B0070:2B Driver Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0070:4A Driver Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0072:11 Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground GO to PINPOINT TEST I .
B0072:12 Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery GO to PINPOINT TEST I .
B0072:13 Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Open GO to PINPOINT TEST I .
B0072:1A Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST I .
B0072:2B Passenger Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0072:4A Passenger Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B007E:11 Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground GO to PINPOINT TEST J .
B007E:12 Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery GO to PINPOINT TEST J .
B007E:13 Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Open GO to PINPOINT TEST J .
B007E:1A Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST J .
B007E:2B Driver Seatbelt Pretensioner "C" Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B007E:4A Driver Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B007F:11 Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground GO to PINPOINT TEST K .
B007F:12 Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery GO to PINPOINT TEST K .
B007F:13 Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open GO to PINPOINT TEST K .
B007F:1A Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST K .
B007F:2B Passenger Seatbelt Pretensioner "C" Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B007F:4A Passenger Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B0082:11 Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground GO to PINPOINT TEST L .
B0082:12 Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery GO to PINPOINT TEST L .
B0082:13 Passenger Seatbelt Load Limiter Deployment Control: Circuit Open GO to PINPOINT TEST L .
B0082:1A Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST L .
B0082:2B Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B0082:4A Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B00A0:09 Occupant Classification System: Component Failure GO to PINPOINT TEST M .
B00A0:4A Occupant Classification System: Incorrect Component Installed GO to PINPOINT TEST M .
B00A0:63 Occupant Classification System: Circuit/Component Protection Time-Out GO to PINPOINT TEST M .
B00A0:64 Occupant Classification System: Signal Plausibility Failure GO to PINPOINT TEST M .
B00A0:68 Occupant Classification System: Event Information GO to PINPOINT TEST M .
B00B5:11 Driver Seat Track Position Restraints Sensor: Circuit Short to Ground GO to PINPOINT TEST N .
B00B5:12 Driver Seat Track Position Restraints Sensor: Circuit Short to Battery GO to PINPOINT TEST N .
B00B5:13 Driver Seat Track Position Restraints Sensor: Circuit Open GO to PINPOINT TEST N .
B00B5:1D Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range GO to PINPOINT TEST N .
B00B5:2B Driver Seat Track Position Restraints Sensor: Signal Cross Coupled GO to PINPOINT TEST Y .
B00B5:4A Driver Seat Track Position Restraints Sensor: Incorrect Component Installed GO to PINPOINT TEST Z .
B00D5:01 Restraint System Passenger Disable Indicator: General Electric Failure The RCM has received a fault message from the FCIM indicating a fault in the PAD indicator. CARRY OUT a self-test of the FCIM and REPAIR any DTCs. Do not replace the RCM for this DTC.
B1193:00 Crash Event Storage Full and Locked: No Sub Type Information This DTC indicates the vehicle has been involved in a crash. INSTALL a new RCM and impact sensors. REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT .
B11CF:11 Passenger Frontal Airbag Canister Vent: Circuit Short to Ground GO to PINPOINT TEST O .
B11CF:12 Passenger Frontal Airbag Canister Vent: Circuit Short to Battery GO to PINPOINT TEST O .
B11CF:13 Passenger Frontal Airbag Canister Vent: Circuit Open GO to PINPOINT TEST O .
B11CF:1A Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold GO to PINPOINT TEST O .
B11CF:2B Passenger Frontal Airbag Canister Vent: Signal Cross Coupled GO to PINPOINT TEST Y .
B11CF:4A Passenger Frontal Airbag Canister Vent: Incorrect Component Installed GO to PINPOINT TEST Z .
B11D8:12 Restraint Event Notification: Circuit Short to Battery GO to PINPOINT TEST P .
B11D8:14 Restraint Event Notification: Circuit Short to Ground or Open GO to PINPOINT TEST P .
B1202:01 Restraint System Passenger Enable Indicator: General Electric Failure The RCM has received a fault message from the FCIM indicating a fault in the PAD indicator. CARRY OUT a self-test of the FCIM and REPAIR any DTCs. Do not replace the RCM for this DTC.
B1404:11 Driver Side Airbag Deployment Control: Circuit Short to Ground GO to PINPOINT TEST Q .
B1404:12 Driver Side Airbag Deployment Control: Circuit Short to Battery GO to PINPOINT TEST Q .
B1404:13 Driver Side Airbag Deployment Control: Circuit Open GO to PINPOINT TEST Q .
B1404:1A Driver Side Airbag Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST Q .
B1404:2B Driver Side Airbag Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B1404:4A Driver Side Airbag Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B1405:11 Driver Curtain Deployment Control 1: Circuit Short to Ground GO to PINPOINT TEST R .
B1405:12 Driver Curtain Deployment Control 1: Circuit Short to Battery GO to PINPOINT TEST R .
B1405:13 Driver Curtain Deployment Control 1: Circuit Open GO to PINPOINT TEST R .
B1405:1A Driver Curtain Deployment Control 1: Circuit Resistance Below Threshold GO to PINPOINT TEST R .
B1405:2B Driver Curtain Deployment Control 1: Signal Cross Coupled GO to PINPOINT TEST Y .
B1405:4A Driver Curtain Deployment Control 1: Incorrect Component Installed GO to PINPOINT TEST Z .
B1407:11 Passenger Side Airbag Deployment Control: Circuit Short to Ground GO to PINPOINT TEST S .
B1407:12 Passenger Side Airbag Deployment Control: Circuit Short to Battery GO to PINPOINT TEST S .
B1407:13 Passenger Side Airbag Deployment Control: Circuit Open GO to PINPOINT TEST S .
B1407:1A Passenger Side Airbag Deployment Control: Circuit Resistance Below Threshold GO to PINPOINT TEST S .
B1407:2B Passenger Side Airbag Deployment Control: Signal Cross Coupled GO to PINPOINT TEST Y .
B1407:4A Passenger Side Airbag Deployment Control: Incorrect Component Installed GO to PINPOINT TEST Z .
B1408:11 Passenger Curtain Deployment Control 1: Circuit Short to Ground GO to PINPOINT TEST T .
B1408:12 Passenger Curtain Deployment Control 1: Circuit Short to Battery GO to PINPOINT TEST T .
B1408:13 Passenger Curtain Deployment Control 1: Circuit Open GO to PINPOINT TEST T .
B1408:1A Passenger Curtain Deployment Control 1: Circuit Resistance Below Threshold GO to PINPOINT TEST T .
B1408:2B Passenger Curtain Deployment Control 1: Signal Cross Coupled GO to PINPOINT TEST Y .
B1408:4A Passenger Curtain Deployment Control 1: Incorrect Component Installed GO to PINPOINT TEST Z .
B1413:11 Driver Frontal Restraints Sensor: Circuit Short to Ground GO to PINPOINT TEST U .
B1413:4A Driver Frontal Restraints Sensor: Incorrect Component Installed GO to PINPOINT TEST Z .
B1413:81 Driver Frontal Restraints Sensor: Invalid Serial Data Received INSTALL a new LH front impact severity sensor. REFER to FRONT IMPACT SEVERITY SENSOR .
B1413:93 Driver Frontal Restraints Sensor: No Operation GO to PINPOINT TEST U .
B1413:96 Driver Frontal Restraints Sensor: Component Internal Failure INSTALL a new LH front impact severity sensor. REFER to FRONT IMPACT SEVERITY SENSOR .
B1414:11 Driver Side Restraints Sensor 1: Circuit Short to Ground GO to PINPOINT TEST V .
B1414:4A Driver Side Restraints Sensor 1: Incorrect Component Installed GO to PINPOINT TEST Z .
B1414:81 Driver Side Restraints Sensor 1: Invalid Serial Data Received INSTALL a new driver door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR .
B1414:93 Driver Side Restraints Sensor 1: No Operation GO to PINPOINT TEST V .
B1414:96 Driver Side Restraints Sensor 1: Component Internal Failure INSTALL a new driver door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR .
B1415:11 Driver Side Restraints Sensor 2: Circuit Short to Ground GO to PINPOINT TEST W .
B1415:4A Driver Side Restraints Sensor 2: Incorrect Component Installed GO to PINPOINT TEST Z .
B1415:81 Driver Side Restraints Sensor 2: Invalid Serial Data Received INSTALL a new second row LH side impact sensor. REFER to SIDE IMPACT SENSOR - C-PILLAR .
B1415:93 Driver Side Restraints Sensor 2: No Operation GO to PINPOINT TEST W .
B1415:96 Driver Side Restraints Sensor 2: Component Internal Failure INSTALL a new second row LH side impact sensor. REFER to SIDE IMPACT SENSOR - C-PILLAR .
B1417:11 Passenger Frontal Restraints Sensor: Circuit Short to Ground GO to PINPOINT TEST X .
B1417:4A Passenger Frontal Restraints Sensor: Incorrect Component Installed GO to PINPOINT TEST Z .
B1417:81 Passenger Frontal Restraints Sensor: Invalid Serial Data Received INSTALL a new RH front impact severity sensor. REFER to FRONT IMPACT SEVERITY SENSOR .
B1417:93 Passenger Frontal Restraints Sensor: No Operation GO to PINPOINT TEST X .
B1417:96 Passenger Frontal Restraints Sensor: Component Internal Failure INSTALL a new RH front impact severity sensor. REFER to FRONT IMPACT SEVERITY SENSOR .
B1418:11 Passenger Side Restraints Sensor 1: Circuit Short to Ground GO to PINPOINT TEST W .
B1418:4A Passenger Side Restraints Sensor 1: Incorrect Component Installed GO to PINPOINT TEST Z .
B1418:81 Passenger Side Restraints Sensor 1: Invalid Serial Data Received INSTALL a new passenger door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR .
B1418:93 Passenger Side Restraints Sensor 1: No Operation GO to PINPOINT TEST W .
B1418:96 Passenger Side Restraints Sensor 1: Component Internal Failure INSTALL a new passenger door side impact sensor. REFER to SIDE IMPACT SENSOR - FRONT DOOR .
B1419:11 Passenger Side Restraints Sensor 2: Circuit Short to Ground GO to PINPOINT TEST V .
B1419:4A Passenger Side Restraints Sensor 2: Incorrect Component Installed GO to PINPOINT TEST Z .
B1419:81 Passenger Side Restraints Sensor 2: Invalid Serial Data Received INSTALL a new second row RH side impact sensor. REFER to SIDE IMPACT SENSOR - C-PILLAR .
B1419:93 Passenger Side Restraints Sensor 2: No Operation GO to PINPOINT TEST V .
B1419:96 Passenger Side Restraints Sensor 2: Component Internal Failure INSTALL a new second row RH side impact sensor. REFER to SIDE IMPACT SENSOR - C-PILLAR .
B142D:00 Pyrotechnic End of Life Activation Performed: No Sub Type Information INSTALL a new RCM and CARRY OUT PMI. Use as-built data when carrying out PMI for this DTC. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U0028:08 Vehicle Communication Bus A: Bus Signal/Message Failures GO to PINPOINT TEST AA .
U0028:88 Vehicle Communication Bus A: Bus Off GO to PINPOINT TEST AA .
U0140:00 Lost Communication With Body Control Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AB .
U0154:00 Lost Communication With Restraints Occupant Classification System Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AC .
U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AD .
U0253:00 Lost Communication With Accessory Protocol Interface Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AE .
U0300:00 Internal Control Module Software Incompatibility: No Sub Type Information CARRY OUT PMI. RETRIEVE RCM DTCs. If RCM DTC U0300:00 is retrieved on-demand during self-test, INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in a pinpoint test.
CHECK for additional RCM and BCM DTCs. REFER to the appropriate section to diagnose the DTCs.
U0422:81 Invalid Data Received From Body Control Module: Invalid Serial Data Received
NOTE: This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in a pinpoint test.
CHECK for BCM DTCs. REFER to MULTIFUNCTION ELECTRONIC MODULES to diagnose the BCM DTCs.
U0554:00 Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in a pinpoint test.
CHECK for additional RCM and APIM DTCs. DIAGNOSE all other RCM DTCs. For vehicles with APIM DTCs, REFER to INFORMATION AND ENTERTAINMENT SYSTEMS8-INCH (203 MM)TOUCHSCREEN, 10 SPEAKERS for vehicles with an 8-inch (203 mm) touchscreen and 10 speakers or REFER to INFORMATION AND ENTERTAINMENT SYSTEMS - THX, 8-INCH (203 MM)TOUCHSCREEN, 16 SPEAKERS for vehicles with THX®, 8-inch (203 mm) touchscreen and 16 speakers.
U0557:82 Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated
NOTE: This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair unless directed to do so in a pinpoint test.
CHECK for FCIM or IPC DTCs. For vehicles with FCIM DTCs, REFER to INFORMATION AND ENTERTAINMENT SYSTEMS8-INCH (203 MM)TOUCHSCREEN, 10 SPEAKERS for vehicles with an 8-inch (203 mm) touchscreen and 10 speakers or REFER to INFORMATION AND ENTERTAINMENT SYSTEMS - THX, 8-INCH (203 MM)TOUCHSCREEN, 16 SPEAKERS for vehicles with THX®, 8-inch (203 mm) touchscreen and 16 speakers. For IPC DTCs, REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES .
U2100:00 Initial Configuration Not Complete: No Sub Type Information CARRY OUT PMI. RETRIEVE RCM DTCs. If RCM DTC U2100:00 is retrieved on-demand, INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CARRY OUT PMI using As-Built data. RETRIEVE RCM DTCs. If RCM DTC U2101:00 is retrieved on-demand, INSTALL a new RCM. Use As-Built data when carrying out PMI for this DTC. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U2200:00 Control Module Configuration Memory Corrupt: No Sub Type Information INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out PMI for this DTC. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U2300:55 Central Configuration: Not Configured GO to PINPOINT TEST AR .
U2300:64 Central Configuration: Signal Plausibility Failure GO to PINPOINT TEST AR .
U3000:46 Control Module: Calibration/Parameter Memory Failure INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U3000:49 Control Module: Internal Electronic Failure INSTALL a new RCM and CARRY OUT PMI. If DTC U2200:00 is also present, use As-Built data when carrying out PMI. REFER to RESTRAINTS CONTROL MODULE (RCM) .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST AF .
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST AF .
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE: Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to DIAGNOSTIC METHODS for information about these practices.
OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) DTC CHART

DTC Description Action To Take
B0061:11 Passenger Seatbelt Tension Sensor: Circuit Short to Ground GO to PINPOINT TEST AG .
B0061:12 Passenger Seatbelt Tension Sensor: Circuit Short to Battery GO to PINPOINT TEST AG .
B0061:13 Passenger Seatbelt Tension Sensor: Circuit Open GO to PINPOINT TEST AG .
B0061:1C Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range GO to PINPOINT TEST AG .
B00A0:54 Occupant Classification System: Missing Calibration GO to PINPOINT TEST AH .
B00A0:67 Occupant Classification System: Signal Incorrect After Event CARRY OUT the OCS Zero Seat Weight Test. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM ZERO SEAT WEIGHT TEST .
B00A0:76 Occupant Classification System: Wrong Mounting Position GO to PINPOINT TEST AH .
B00A0:97 Occupant Classification System: Component or System Operation Obstructed or Blocked GO to PINPOINT TEST AI .
B00C2:12 Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery GO to PINPOINT TEST AJ .
B00C2:13 Passenger Seat Occupant Classification Sensor "C": Circuit Open GO to PINPOINT TEST AJ .
B00C2:1A Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Below Threshold GO to PINPOINT TEST AJ .
B00C2:49 Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure GO to PINPOINT TEST AH .
B00C2:81 Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data Received REPAIR all other OCSM DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING .
B00C3:12 Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery GO to PINPOINT TEST AK .
B00C3:13 Passenger Seat Occupant Classification Sensor "D": Circuit Open GO to PINPOINT TEST AK .
B00C3:1A Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Below Threshold GO to PINPOINT TEST AK .
B00C3:49 Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure GO to PINPOINT TEST AH .
B00C3:81 Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data Received REPAIR all other OCSM DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING .
B1193:00 Crash Event Storage Full and Locked: No Sub Type Information INSTALL a new passenger seat track assembly with weight sensor bolts. REFER to SEATING . CLEAR all DTCs before carrying out the System Reset procedure.
B1A59:01 Sensor 5 Volt Supply: General Electrical Failure GO to PINPOINT TEST AL .
B1A59:11 Sensor 5 Volt Supply: Circuit Short to Ground GO to PINPOINT TEST AL .
U0100:00 Lost Communication With ECM/PCM "A": No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AM .
U0140:00 Lost Communication With Body Control Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AN .
U0151:00 Lost Communication With Restraints Control Module: No Sub Type Information
NOTE: This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test.
GO to PINPOINT TEST AO .
U0401:00 Invalid Data Received From ECM/PCM "A": No Sub Type Information U0401:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00. CARRY OUT the PCM self test. REPAIR any vehicle speed or communication-related DTCs. REFER to the DTC CHART in ENGINE CONTROLS - POWERTRAIN DTC CHARTS & DESCRIPTIONS (SECTION 4) .
U0401:81 Invalid Data Received From ECM/PCM "A": Invalid Serial Data Received This DTC sets when the OCSM is not receiving the vehicle speed data that it expects from the PCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:81. CARRY OUT the PCM self test. REPAIR any DTCs. REFER to the DTC CHART in ELECTRONIC ENGINE CONTROLS or the ENGINE CONTROLS - POWERTRAIN DTC CHARTS & DESCRIPTIONS (SECTION 4) .
U0422:00 Invalid Data Received From ECM/PCM "A": No Sub Type Information U0422:00 sets in a module that is reporting a communication fault from another module on the data bus. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:00. CARRY OUT the BCM self test. REPAIR any ignition switch or communication-related DTCs. REFER to BODY CONTROL MODULE (BCM) - DTC chart .
U0422:81 Invalid Data Received From ECM/PCM "A": Invalid Serial Data Received U0422:81 sets when the OCSM is not receiving the ignition status data that it expects from the BCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:81. CARRY OUT the BCM self test. REPAIR any ignition switch or communication-related DTCs. REFER to BODY CONTROL MODULE (BCM) - DTC chart .
U0452:00 Invalid Data Received From Restraints Control Module: No Sub Type Information U0452:00 sets in a module that is reporting a communication fault from another module on the data bus. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:00. CARRY OUT RCM self test. REPAIR any SRS-related DTCs. REFER to the RCM DTC Chart .
U0452:81 Invalid Data Received From Restraints Control Module: No Sub Type Information U0452:00 sets when the OCSM is not receiving the SRS data that it expects from the RCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:81. CARRY OUT RCM self test. REPAIR any SRS-related DTCs. REFER to the RCM DTC Chart .
U200D:12 Control Module Output Power A: Circuit Short To Battery GO to PINPOINT TEST AP .
U200E:11 Control Module Output Power B: Circuit Short To Ground GO to PINPOINT TEST AQ .
U200E:12 Control Module Output Power B: Circuit Short To Battery GO to PINPOINT TEST AQ .
U200E:1A Control Module Output Power B: Circuit Resistance Below Threshold GO to PINPOINT TEST AQ .
U3000:49 Control Module: Internal Electronic Failure REPAIR all other OCSM DTCs first. REPEAT the self-test. If U3000:49 returns, INSTALL a new OCSM. REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) .
U3000:53 Control Module: Deactivated CLEAR all OCSM DTCs and REPEAT the self-test. If U3000:53 returns, INSTALL a new OCSM. REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) .
U3000:54 Control Module: Missing Calibration CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST AF .
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST AF .
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE: Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to DIAGNOSTIC METHODS for information about these practices.
FRONT CONTROLS INTERFACE MODULE (FCIM) DTC CHART

DTC Description Action To Take
B00D5:01 Restraint System Passenger Disable Indicator: General Electric Failure REFER to INFORMATION AND ENTERTAINMENT SYSTEMS8-INCH (203 MM)TOUCHSCREEN, 10 SPEAKERS for vehicles with an 8-inch (203 mm) touchscreen and 10 speakers or REFER to INFORMATION AND ENTERTAINMENT SYSTEMS - THX, 8-INCH (203 MM)TOUCHSCREEN, 16 SPEAKERS for vehicles with THX®, 8-inch (203 mm) touchscreen and 16 speakers to diagnose this DTC.
B1202:01 Restraint System Passenger Enable Indicator: General Electric Failure REFER to INFORMATION AND ENTERTAINMENT SYSTEMS8-INCH (203 MM)TOUCHSCREEN, 10 SPEAKERS for vehicles with an 8-inch (203 mm) touchscreen and 10 speakers or REFER to INFORMATION AND ENTERTAINMENT SYSTEMS - THX, 8-INCH (203 MM)TOUCHSCREEN, 16 SPEAKERS for vehicles with THX®, 8-inch (203 mm) touchscreen and 16 speakers to diagnose this DTC.
scientia non olet · About LEMON Manuals