LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 350h >> Repair and Diagnosis >> External Pages >> Different car >> Section 16 (Engine Mechanical System - Service Information (1 Of 4)) >> Cylinder Head Gasket >> Removal [11/2021 - 03/2024] >> Procedure

Removal [11/2021 - 03/2024]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY 

    Refer to REMOVAL [11/2021 - 03/2024] 

  2. REMOVE DRIVE SHAFT BEARING BRACKET 

    Refer to PROCEDURE - Step 1

  3. REMOVE FUEL DELIVERY GUARD 

    Refer to PROCEDURE - Step 9

  4. DISCONNECT NO. 1 TURBO WATER HOSE 

    Refer to PROCEDURE - Step 11

  5. DISCONNECT NO. 3 WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 13

  6. DISCONNECT NO. 4 TURBO WATER HOSE 

    Refer to PROCEDURE - Step 15

  7. DISCONNECT NO. 4 WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 17

  8. DISCONNECT NO. 5 WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 18

  9. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE 
    Refer to PROCEDURE - Step 13
  10. REMOVE INTAKE MANIFOLD WITH INTERCOOLER ASSEMBLY 

    Refer to PROCEDURE - Step 20

  11. REMOVE WATER CONTROL VALVE 

    Refer to PROCEDURE - Step 10

  12. REMOVE FRONT WATER BY-PASS JOINT 

    Refer to PROCEDURE - Step 16

  13. REMOVE WATER OUTLET GASKET 

    Refer to PROCEDURE - Step 17

  14. REMOVE NO. 1 TURBO INSULATOR 

    Refer to PROCEDURE - Step 21

  15. REMOVE MANIFOLD STAY 

    Refer to PROCEDURE - Step 25

  16. REMOVE NO. 1 TURBO OIL PIPE 

    Refer to PROCEDURE - Step 26

  17. REMOVE NO. 1 TURBO OIL OUTLET GASKET 

    Refer to PROCEDURE - Step 27

  18. REMOVE TURBOCHARGER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 28

  19. REMOVE NO. 2 WATER BY-PASS PIPE 

    Refer to PROCEDURE - Step 35

  20. REMOVE FUEL DELIVERY PIPE 
    Refer to PROCEDURE - Step 13 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 14 [03/2023 - ]
  21. REMOVE FUEL DELIVERY SPACER 

    Refer to PROCEDURE - Step 14 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 15 [03/2023 - ]

  22. REMOVE INJECTOR VIBRATION INSULATOR 

    Refer to PROCEDURE - Step 15 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 16 [03/2023 - ]

  23. REMOVE NO. 5 ENGINE WIRE 

    Refer to PROCEDURE - Step 16 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 17 [03/2023 - ]

  24. REMOVE PORT FUEL INJECTOR ASSEMBLY 
    Refer to PROCEDURE - Step 17 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 18 [03/2023 - ]
  25. REMOVE WIRE HARNESS 
    Refer to PROCEDURE - Step 42
  26. REMOVE WATER INLET HOUSING 

    Refer to PROCEDURE - Step 43

  27. REMOVE NO. 2 MANIFOLD STAY 

    Refer to PROCEDURE - Step 44

  28. REMOVE HEATER WATER HOSE BRACKET 

    Refer to PROCEDURE - Step 49

  29. REMOVE SPARK PLUG 
    Refer to PROCEDURE - Step 4 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 5 [03/2023 - ]
  30. REMOVE OIL COOLER ASSEMBLY 

    Refer to PROCEDURE - Step 4

  31. REMOVE OIL COOLER GASKET 

    Refer to PROCEDURE - Step 5

  32. REMOVE OIL COOLER PIPE GASKET 

    Refer to PROCEDURE - Step 6

  33. REMOVE CYLINDER HEAD SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 52
  34. REMOVE CYLINDER HEAD GASKET 
    1. GTY1077730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. INSPECT CYLINDER HEAD SET BOLT 

    Refer to PROCEDURE - Step 21

  36. INSPECT CYLINDER HEAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 1

scientia non olet · About LEMON Manuals