LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 250 FWD >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Heating / Air Conditioning System - Service Information (3 Of 3) >> COMPRESSOR (for A25A-FXS) >> Removal [11/2021 - ] >> Procedure

Removal [11/2021 - ]: Procedure

  1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM 

    Refer to PROCEDURE - Step 1

  2. REMOVE SERVICE PLUG GRIP 

    Refer to REMOVAL [11/2021 - ]

  3. REMOVE NO. 2 INVERTER PROTECTOR 

    Refer to PROCEDURE - Step 8

  4. DISCONNECT ENGINE ROOM MAIN WIRE 
    Refer to PROCEDURE - Step 4
  5. REMOVE CONNECTOR COVER ASSEMBLY 
    Refer to PROCEDURE - Step 10
  6. CHECK TERMINAL VOLTAGE 
    Refer to PROCEDURE - Step 11
  7. INSTALL CONNECTOR COVER ASSEMBLY 
    Refer to PROCEDURE - Step 8
  8. CONNECT ENGINE ROOM MAIN WIRE 
    Refer to PROCEDURE - Step 31
  9. INSTALL NO. 2 INVERTER PROTECTOR 

    Refer to PROCEDURE - Step 18

  10. REMOVE FRONT WHEEL RH 

    Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

  11. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH 
    Use the same procedure described for the LH side.
    Refer to PROCEDURE - Step 3 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 3 [03/2024 - ]
  12. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 7 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 7 [03/2024 - ]

  13. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 8 [03/2024 - ]

  14. REMOVE FRONT FENDER LINER RH 
    1. Use the same procedure described for the LH side.

      Refer to PROCEDURE - Step 8 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 8 [03/2024 - ]

  15. REMOVE FRONT FENDER APRON SEAL RH 

    Refer to PROCEDURE - Step 12 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 12 [03/2024 - ]

  16. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 9 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 9 [03/2024 - ]

  17. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 10 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 10 [03/2024 - ]

  18. DISCONNECT SUCTION HOSE SUB-ASSEMBLY 
    1. GTY1070903Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor with motor assembly.
      2. Remove the O-ring from the suction hose sub-assembly.
        NOTE:

        Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  19. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY 
    1. GTY1070285Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the bolt and disconnect the discharge hose sub-assembly from the compressor with motor assembly.
      2. Remove the O-ring from the discharge hose sub-assembly.
        NOTE:

        Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  20. REMOVE COMPRESSOR WITH MOTOR ASSEMBLY 
    1. GTY1070079Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Connector (A) *b Connector (B)
      *c Green-colored Lock - -
      Slide - -
      1. Slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.
        WARNING:

        Make sure to wear insulated gloves.

        NOTE:

        Insulate the disconnected terminals and connector (A) with insulating tape.

      2. Disconnect the connector (B).
    2. GTY1071308Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      1. Remove the bolt and 2 nuts.
      2. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.
      3. Remove the compressor with motor assembly as shown in the illustration.
scientia non olet · About LEMON Manuals