LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 85 (Engine Cooling System - Service Information) >> Radiator >> Removal [11/2021 - ] >> Procedure

Removal [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 8 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 8 [03/2024 - ]

  2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 9 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 9 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 9 [03/2024 - ]

  3. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 10 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 10 [03/2024 - ]

  4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 11 [03/2023 - 03/2024] , or refer to PROCEDURE - Step 11 [03/2024 - ]

  5. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 4

  6. REMOVE FRONT BUMPER ASSEMBLY 

    for Sport Package: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

    except Sport Package: Refer to REMOVAL [11/2021 - 03/2024] , or refer to REMOVAL [03/2024 - ]

  7. REMOVE FRONT NO. 2 BUMPER ENERGY ABSORBER 

    Refer to PROCEDURE - Step 45 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 46 [03/2022 - ]

  8. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 50 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 51 [03/2022 - ]

  9. REMOVE HEADLIGHT ASSEMBLY LH 

    for LED Type Turn Signal Light: Refer to REMOVAL [11/2021 - ]

    for Bulb Type Turn Signal Light: Refer to REMOVAL [11/2021 - ]

  10. REMOVE HEADLIGHT ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  11. REMOVE INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 4

  12. REMOVE HOOD SUPPORT TENSION SPRING 
    Refer to PROCEDURE - Step 3 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 3 [03/2022 - ]
  13. REMOVE HOOD LOCK CONTROL COVER 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 8 [03/2022 - ]

  14. DISCONNECT HOOD LOCK CONTROL CABLE AND LEVER SET 

    Refer to PROCEDURE - Step 9 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 9 [03/2022 - ]

  15. REMOVE HOOD LOCK CONTROL JUNCTION ASSEMBLY 

    Refer to PROCEDURE - Step 10 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 10 [03/2022 - ]

  16. REMOVE HOOD LOCK ASSEMBLY LH 

    Refer to PROCEDURE - Step 11 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 11 [03/2022 - ]

  17. REMOVE HOOD LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH 

    Refer to PROCEDURE - Step 12 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 12 [03/2022 - ]

  18. REMOVE THERMISTOR ASSEMBLY 

    Refer to REMOVAL [11/2021 - ]

  19. REMOVE NO. 1 RADIATOR AIR GUIDE LH 
    1. GTY1077221Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE NO. 1 RADIATOR AIR GUIDE RH 
    1. GTY1077223Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY 
    1. GTY1077234Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. DISCONNECT NO. 5 WATER BY-PASS HOSE 
    1. GTY1077591Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. DISCONNECT NO. 6 WATER BY-PASS HOSE 
    1. GTY1077200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. DISCONNECT NO. 1 RADIATOR HOSE 
    1. GTY1077201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. DISCONNECT NO. 2 RADIATOR HOSE 
    1. GTY1077202Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE RADIATOR ASSEMBLY 
    1. GTY1076451Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the cooling fan motor connector.
      2. Disengage the clamp to disconnect the wire harness from the fan with motor assembly.
      3. Rotate the lever while pushing the lock, and disconnect the cooling fan motor connector.
        NOTE:

        After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector.

      4. Disengage the 2 clamps to disconnect the wire harness from the fan with motor assembly.
    2. GTY1076810Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disengage the 2 claws.
      2. Disengage the 2 guides to separate the cooler condenser assembly and radiator assembly (for intercooler) from the radiator assembly.
        NOTE:

        Make sure not to damage the cooler condenser assembly or radiator assembly (for intercooler) when removing the radiator assembly.

      3. Remove the radiator assembly with the fan with motor assembly from the vehicle body.
        NOTE:

        Do not apply excessive force to the cooler condenser assembly, radiator assembly (for intercooler) or pipe when removing the radiator assembly.

    3. GTY1077299Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disengage the 2 claws.
      2. Disengage the 2 guides to remove the fan with motor assembly from the radiator assembly.
        NOTE:

        Do not damage the radiator assembly when removing the fan with motor assembly.

  27. REMOVE RADIATOR SUPPORT CUSHION 
    1. GTY1077273Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. REMOVE LOWER RADIATOR SUPPORT 
    1. GTY1077274Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals