LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 57 (Automatic Transaxle System - Service Information (1 Of 2)) >> Oil Cooler >> Installation [11/2021 - ] >> Procedure

Installation [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL TRANSMISSION OIL COOLER 
    1. GTY1062989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Install the transmission oil cooler to the automatic transaxle case sub-assembly with the 3 bolts.

        Torque: 13.5 N.m (138 kgf/cm, 10 ft.lbf) 

        HINT: 

        Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt ((B) → (C) → (A))

  2. CONNECT OUTLET NO. 1 OIL COOLER HOSE 
    1. GTY1063082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 0 to 3 mm (0 to 0.118 in.) *b 2 to 7 mm (0.0787 to 0.276 in.)
      *c Paint Mark *d 30° (Paint Mark Location)
      1. Connect the outlet No. 1 oil cooler hose to the transmission oil cooler and slide the clip to secure it.
        NOTE:
        • Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.
        • Make sure to align the paint mark of the outlet No. 1 oil cooler hose with paint mark of the transmission oil cooler.
        • Make sure that the paint mark of the outlet No. 1 oil cooler hose and clip are within the location shown in the illustration.
  3. CONNECT INLET NO. 1 OIL COOLER HOSE 
    1. GTY1061679Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 0 to 3 mm (0 to 0.118 in.) *b 2 to 7 mm (0.0787 to 0.276 in.)
      *c Paint Mark - -
      1. Connect the inlet No. 1 oil cooler hose to the transmission oil cooler and slide the clip to secure it.
        NOTE:
        • Make sure to slide the inlet No. 1 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.
        • Make sure to align the paint mark of the inlet No. 1 oil cooler hose with the paint mark of the transmission oil cooler.
        • Make sure that the clip is within the location shown in the illustration.
  4. CONNECT WATER BY-PASS HOSE ASSEMBLY 
    1. GTY1063126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 2 to 7 mm (0.0787 to 0.276 in.) *b Paint Mark
      *c 60° (Claw of Clip Location) - -
      1. Connect the water by-pass hose assembly to the transmission oil cooler and slide the 2 clips to secure it.
        NOTE:
        • Make sure to slide the water by-pass hose assembly until it contacts the hose stopper of the transmission oil cooler.
        • Make sure to align the paint mark of the water by-pass hose assembly with the paint mark of the transmission oil cooler.
        • Make sure that the claws of the clip are within the location shown in the illustration.
  5. INSTALL NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP 
  6. INSTALL ENGINE WIRE 
  7. INSTALL AIR CLEANER ASSEMBLY 
    Refer to PROCEDURE - Step 4
  8. INSTALL INLET AIR CLEANER ASSEMBLY 
    Refer to PROCEDURE - Step 5
  9. INSTALL RADIATOR UPPER AIR GUIDE PLATE 
  10. ADD ENGINE COOLANT 

    Refer to PROCEDURE - Step 5

  11. ADJUST AUTOMATIC TRANSAXLE FLUID 

    Refer to ADJUSTMENT [11/2021 - ] 

  12. INSPECT FOR ENGINE COOLANT LEAK 

    Refer to PROCEDURE - Step 1

  13. INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK 
  14. INSTALL SUSPENSION TOWER DAMPER (w/ Damper) 
    Refer to PROCEDURE - Step 1
  15. INSTALL FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 80 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 81 [03/2023 - ]

  16. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 82 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 83 [03/2023 - ]

  17. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 83 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 84 [03/2023 - ]

  18. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 84 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 85 [03/2023 - ]

  19. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 85 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 86 [03/2023 - ]

scientia non olet · About LEMON Manuals