LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> RC 350 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 63 (Automatic Transmission System (2GR-FSE,A760H) - Diagnostic Codes (2 Of 2) & Circuit Tests) >> AUTOMATIC TRANSMISSION SYSTEM (for 2GR-FSE) >> DTC P2757: Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) [09/2014 - 11/2017] >> Procedure

DTC P2757: Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) [09/2014 - 11/2017]: Procedure

WARNING: This page is about a different car, the 2017 Lexus RC 350, 2017 Lexus RC 300, 2016 Lexus RC 350, 2016 Lexus RC 300, and 2015 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK OTHER DTCS OUTPUT 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine > Trouble Codes 

    4. Read the DTCs using the Techstream.

      Result

      Result Proceed to
      Only DTC P2757 is output A
      P2757 and other DTCs are output B

      HINT: 

      If any DTCs other than P2757 are output, perform troubleshooting for those DTCs first.

    Result: 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2014 - 10/2015]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2015 - 11/2017] 

    Result: 

    See step  2

  2. INSPECT SHIFT SOLENOID VALVE SLU 
    1. Remove the shift solenoid valve SLU.
      GTY469146Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Shift Solenoid Valve SLU
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

      OK

      The solenoid makes an operating sound.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SHIFT SOLENOID VALVE SLU. Refer to  COMPONENTS [09/2014 - ] 

    Result: 

    OK 

    See step  3

  3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY 
    1. Check the transmission valve body assembly.

      Refer to REMOVAL [09/2014 - ]

      OK

      There is no foreign matter on each valve and they operate smoothly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY. Refer to  COMPONENTS [09/2014 - ] 

    Result: 

    OK 

    See step  4

  4. INSPECT TORQUE CONVERTER ASSEMBLY 
    1. Check the torque converter assembly.

      Refer to INSPECTION [09/2014 - ]

      OK

      The torque converter assembly operates normally.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPAIR OR REPLACE AUTOMATIC TRANSMISSION WITH TRANSFER ASSEMBLY. Refer to  COMPONENTS [09/2014 - 11/2017] 

    Result: 

    NG 

    REPLACE TORQUE CONVERTER ASSEMBLY. Refer to  COMPONENTS [09/2014 - 11/2017]