Installation [10/2024 - ]: Procedure

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from top	-	-
   	Front of the vehicle		Right of the vehicle

   1. Temporarily attach a new rear suspension member front body mounting cushion LH to the rear suspension member sub-assembly in the direction shown in the figure.
      NOTE:

      • The rear suspension member front body mounting cushion LH is installed in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion LH.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Turn

   *b

   Hold

   1. Install the SST as shown.
      • SST: 09830-10010 
        1. 09830-01010
        2. 09830-01020
        3. 09830-01040
        4. 09830-01050
      • SST: 09570-24011 
      NOTE:

      Before using SST, apply molybdenum grease to the center bolt of SST.

   2. Using SST, press the rear suspension member front body mounting cushion LH into the rear suspension member sub-assembly until there is no gap at the position shown in the illustration.
      • SST: 09830-10010 
        1. 09830-01010
        2. 09830-01020
        3. 09830-01040
        4. 09830-01050
      • SST: 09570-24011 
      NOTE:

      If the rear suspension member sub-assembly is scratched, apply chassis black to the scratched areas.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from top	-	-
   	Front of the vehicle		Right of the vehicle

   1. Temporarily attach a new rear suspension member front body mounting cushion RH to the rear suspension member sub-assembly in the direction shown in the figure.
      NOTE:

      • The rear suspension member front body mounting cushion RH is installed in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion RH.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from underneath	-	-
   	Front of the vehicle		Right of the vehicle

   1. Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.
      NOTE:

      • Position the rear suspension member rear body mount cushion LH in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Turn

   *b

   Hold

   1. Install the SST as shown.
      • SST: 09710-28031 
        1. 09711-02030
        2. 09711-02040
        3. 94622-51200
      • SST: 09950-60021 
        1. 09951-00720
        2. 09951-00890
      NOTE:

      Before using SST, apply molybdenum grease to the center bolt of SST.

   2. Using SST, press the rear suspension member rear body mount cushion LH into the rear suspension member sub-assembly until there is no gap in the position shown.
      • SST: 09710-28031 
        1. 09711-02030
        2. 09711-02040
        3. 94622-51200
      • SST: 09950-60021 
        1. 09951-00720
        2. 09951-00890
      NOTE:

      If the rear suspension member sub-assembly is scratched, apply chassis black to the scratched areas.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from underneath	-	-
   	Front of the vehicle		Right of the vehicle

   1. Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.
      NOTE:

      • Position the rear suspension member rear body mount cushion RH in the correct direction.
      • Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.

Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Engine Lifter	*b	Attachment
   	Attachment Placement Location	-	-

   1. Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
      WARNING:

      • The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
      • If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NOTE:

      • Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
      • Keep supporting the rear suspension member sub-assembly until the installation has been completed.
   2. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.
   3. Install the rear suspension member sub-assembly with the rear suspension member rear lower brace LH and rear suspension member rear lower brace RH, 2 bolts and 4 nuts.

      Bolt A 

      Torque: 175 N.m (1785 kgf/cm, 129 ft.lbf) 

      Nut B 

      Torque: 175 N.m (1785 kgf/cm, 129 ft.lbf) 

      Nut C 

      Torque: 18 N.m (184 kgf/cm, 13 ft.lbf) 

w/ Height Control Sensor:

Torque: 12 N.m (122 kgf/cm, 9 ft.lbf) 

Refer to INSTALLATION [10/2022 - ]

Refer to ADJUSTMENT [08/2023 - ]