LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> RX 350h Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 13 (Engine Intake / Exhaust System - Service Information) >> TURBOCHARGER (for Gasoline Model) >> Installation [10/2022 - ] >> Procedure

Installation [10/2022 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2025 Lexus RX 500h, 2025 Lexus RX 350, 2024 Lexus RX 500h, 2024 Lexus RX 350, and 2023 Lexus RX 500h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY 
    1. GTY1078007Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Install a new gasket as shown in the illustration.
      2. Install the No. 1 turbo water pipe sub-assembly with the bolt and 2 nuts.

        Torque: 12 N.m (122 kgf/cm, 9 ft.lbf) 

  2. INSTALL TURBINE OUTLET ELBOW GASKET 
    1. GTY1131916Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Install a new turbine outlet elbow gasket to the converter with catalyst assembly.
        NOTE:
        • Turbine outlet elbow gaskets are located in the grooves all around.
        • After assembly, remove any peeling residue on the flange surface.
  3. INSTALL TURBOCHARGER SUB-ASSEMBLY 
    1. GTY1131382Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Rotatory direction - -
      1. Rotate the converter with catalyst assembly in vehicle outer side to secure removal space.
      2. Using an E10 "TORX" socket wrench, install the 4 stud bolts.

        Torque: 19.5 N.m (199 kgf/cm, 14 ft.lbf) 

      3. Temporarily install the turbocharger sub-assembly and cylinder head with the 4 new nuts.
      4. Install the No. 1 turbo oil pipe and turbocharger sub-assembly with the 2 nuts.

        Torque: 12 N.m (122 kgf/cm, 9 ft.lbf) 

        NOTE:

        Do not apply excessive force to the turbocharger sub-assembly and No. 1 turbo oil pipe.

      5. Install the turbocharger sub-assembly with the 4 nuts in the order shown in the illustration.

        Torque: 43 N.m (438 kgf/cm, 32 ft.lbf) 

        NOTE:

        After tightening the 4 nuts to the specified torque, tighten the first nut again.

  4. INSTALL EXHAUST PIPE CLAMP 
    Refer to PROCEDURE - Step 2
  5. INSTALL CONVERTER WITH CATALYST ASSEMBLY 

    Refer to PROCEDURE - Step 3

  6. INSTALL NO. 1 HEAT INSULATOR BRACKET 
    1. GTY1131913Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *A 

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

      *B 

      Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  7. CONNECT NO. 2 TURBO WATER HOSE 
    1. GTY1131082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Paint Mark (White) - -
      1. Connect the No. 2 turbo water hose.
  8. CONNECT NO. 3 TURBO WATER HOSE 
    1. GTY1131084Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Paint Mark (Yellow) - -
      1. Connect the No. 3 turbo water hose.
  9. INSTALL NO. 1 TURBO INSULATOR 

    Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  10. INSTALL AIR FUEL RATIO SENSOR (for Sensor 1) 
    Refer to PROCEDURE - Step 1

    Specified tightening torque 

    Torque: 44 N.m (449 kgf/cm, 32 ft.lbf) 

  11. INSTALL DASH PANEL HEAT INSULATOR 

    Torque: 4.9 N.m (50 kgf/cm, 43 in.lbf) 

  12. INSTALL COMPRESSOR INLET ELBOW SUB-ASSEMBLY 
    1. GTY1130228Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protrusion - -
      1. Install a new throttle body gasket to the compressor inlet elbow sub-assembly with the protrusion of the throttle body gasket oriented as shown in the illustration.
      2. Install the compressor inlet elbow sub-assembly and turbocherger sub-assembly with the 2 nuts.

        Torque: 21 N.m (214 kgf/cm, 15 ft.lbf) 

  13. INSTALL VACUUM REGULATING VALVE ASSEMBLY 
    Refer to PROCEDURE - Step 1

    Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  14. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 
  15. INSTALL AIR TUBE ASSEMBLY 
    See step  15

    Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  16. CONNECT NO. 1 VENTILATION PRESSURE SENSOR HOSE 
  17. CONNECT PURGE VALVE (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY) 

    Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  18. CONNECT ENGINE WIRE 

    Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  19. INSTALL NO. 2 ENGINE COVER SUB-ASSEMBLY 

    See step  19

  20. INSTALL NO. 3 ENGINE COVER 
    Refer to PROCEDURE - Step 55
  21. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 56
  22. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY 
  23. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY 

    Refer to INSTALLATION [10/2022 - ]

  24. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2WD) 

    See step  1

  25. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD) 

    Refer to INSTALLATION [10/2022 - ]

  26. ADD COOLANT (for Inter cooler) 

    Refer to PROCEDURE - Step 5

  27. INSPECT FOR COOLANT LEAK (for Intercooler) 

    See step  1

  28. INSPECT FOR EXHAUST GAS LEAK 

    See step  3

  29. PERFORM INITIALIZATION 

    Refer to INITIALIZATION [10/2022 - ]

scientia non olet · About LEMON Manuals