Installation [08/2020 - 09/2022]: Procedure

INSTALL DCM (TELEMATICS TRANSCEIVER)
INSTALL NO. 1 TELEPHONE BRACKET
1. Install the No. 1 telephone bracket with the screw.
INSTALL TELEPHONE BRACKET
1. Install the telephone bracket with the screw.
INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
1. Connect each connector.
2. Install the DCM (telematics transceiver) with bracket with the 2 nuts.
  
  Fig 1: DCM (Telematics Transceiver) With Bracket Tightening Sequence [08/2020 - 09/2022]
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
  
  HINT:
  
  Install the nuts in the order shown in the illustration.
INSTALL RADIO RECEIVER ASSEMBLY WITH SWITCH
Refer to PROCEDURE - Step 7
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 28 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 33 [08/2021 - ]
INSTALL LOWER INSTRUMENT PANEL LH
Refer to PROCEDURE - Step 29 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 34 [08/2021 - ]
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 31 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 36 [08/2021 - ]
INSTALL INSTRUMENT SIDE PANEL RH
Refer to PROCEDURE - Step 32 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 37 [08/2021 - ]
INSTALL FRONT DOOR OPENING TRIM COVER RH
HINT:

Use the same procedure as for the LH side.

Refer to PROCEDURE - Step 31
INSTALL COWL SIDE TRIM BOARD RH
HINT:

Use the same procedure as for the LH side.

Refer to PROCEDURE - Step 32
INSTALL FRONT DOOR SCUFF PLATE RH
HINT:

Use the same procedure as for the LH side.

Refer to PROCEDURE - Step 33
INSTALL LOWER INSTRUMENT PANEL
Refer to PROCEDURE - Step 37 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 42 [08/2021 - ]
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 4
INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 5
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
for UA80E:

Refer to PROCEDURE - Step 1

for P710:

Refer to PROCEDURE - Step 1

UB80F:

Refer to PROCEDURE - Step 1
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 7
INSTALL INSTRUMENT PANEL FINISH PANEL END RH
Refer to PROCEDURE - Step 8
INSTALL INSTRUMENT PANEL FINISH PANEL END LH
Refer to PROCEDURE - Step 9
PERFORM DCM ACTIVATION
HINT:

After replacing the DCM (telematics transceiver), make sure to perform DCM activation.

for HV Model: Refer to DCM ACTIVATION [10/2019 - ]

for Gasoline Model: Refer to DCM ACTIVATION [10/2019 - ]
PERFORM REGISTRATION
*: for Lexus Enform Remote Compatible Type

HINT:

After replacing the DCM (telematics transceiver), make sure to perform code registration (Smart access system with push-button start (for Start Function)).

for HV Model: Refer to REGISTRATION [10/2019 - 09/2022]

for Gasoline Model: Refer to REGISTRATION [08/2020 - 09/2022]