DTC P0710-15: Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open [12/2017 - ]: Procedure

1. Warm up the engine.
2. Turn the engine switch off.
3. Connect the Techstream to the DLC3.
4. Turn the engine switch on (IG).
5. Turn the Techstream on.
6. Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No. 1.
7. Read the Data List according to the display on the Techstream.

   Powertrain > Transmission > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   A/T Oil Temperature No. 1	ATF temperature sensor value	Min.: -40°C (-40°F) Max.: 150°C (302°F)	Approximately 80°C (176°F): After stall speed test Equal to ambient temperature: When engine is cold	If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted

   Powertrain > Transmission > Data List 

   Tester Display
   A/T Oil Temperature No. 1

   Result

   Result	Proceed to
   Data List value is normal	A
   Data List value is not normal	B

Result: 

A 

See step  3

Result: 

B 

See step  2

1. Disconnect the D2 ECM connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   D2-86 (THO1) - D2-133 (ETHW)	Always	79 Ω to 156 kΩ
   D2-133 (ETHW) - Other terminals	Always	10 kΩ or higher
   D2-86 (THO1) - Other terminals	Always	10 kΩ or higher

   HINT: 

   If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

   ATF Temperature	Specified Condition
   10°C (50°F)	5 to 8 kΩ
   25°C (77°F)	2.5 to 4.5 kΩ
   110°C (230°F)	0.22 to 0.28 kΩ

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Replace the ECM.

   Refer to COMPONENTS [09/2015 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

PERFORM A/T CODE REGISTRATION. Refer to  REGISTRATION [09/2015 - ] 

1. Disconnect the D56 transmission wire connector.
2. Disconnect the D2 ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   D56-8 (OIL) - D2-86 (THO1)	Always	Below 1 Ω
   D56-9 (E2) - D2-133 (ETHW)	Always	Below 1 Ω
   D56-8 (OIL) or D2-86 (THO1) - Other terminals	Always	10 kΩ or higher
   D56-9 (E2) or D2-133 (ETHW) - Other terminals	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR). Refer to  COMPONENTS [09/2015 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)