Installation [12/2021 - ]: Procedure

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Manual Detent Spring Cover	*2	Manual Detent Spring Sub-assembly
   *3	Manual Valve Lever Sub-assembly	*4	No. 1 ATF Temperature Sensor
   *5	No. 2 ATF Temperature Sensor	*6	Lock Plate

   1. Coat 3 new brake drum gaskets with ATF.
   2. Install the 3 brake drum gaskets to the automatic transmission case sub-assembly as shown in the illustration.
      NOTE:

      Install the steel pipe side facing the transmission valve body assembly side.

   3. Coat 4 new gaskets with ATF and install them to the automatic transmission case sub-assembly.
   4. Install the transmission valve body assembly to the automatic transmission case sub-assembly with the 12 bolts.

      Torque: 11 N.m (112 kgf/cm, 8 ft.lbf) 

      NOTE:

      Take care that the transmission wire does not become trapped.

   5. Install the manual detent spring sub-assembly and manual detent spring cover to the automatic transmission case sub-assembly with the bolt.

      Torque: 9.8 N.m (100 kgf/cm, 87 in.lbf) 

   6. Coat 2 new O-rings with the ATF and install it to the No. 1 ATF temperature sensor and No. 2 ATF temperature sensor.
   7. Connect the No. 1 ATF temperature sensor and No. 2 ATF temperature sensor to the transmission valve body assembly with the 2 bolts and 2 lock plates.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

   8. Install the wire harness clamp to the transmission valve body assembly with the bolt.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

   9. Connect the transmission wire to the wire harness clamp.
   10. Connect the 11 solenoid valve connectors.

Torque: 19.5 N.m (199 kgf/cm, 14 ft.lbf) 

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   	Bolt A		Bolt B
   	Bolt C		Bolt D

   1. Coat a new O-ring with the ATF.
   2. Install the O-ring to the valve body oil strainer assembly.
   3. Temporarily install the valve body oil strainer assembly to the transmission valve body assembly with the 4 bolts.
   4. Tighten the 4 bolts in the tightening order.

      Torque: 9.5 N.m (97 kgf/cm, 84 in.lbf) 

      HINT: 

      Tightening order: Temporarily install bolt A → Tighten bolt B → Tighten bolt C → Tighten bolt D → Tighten bolt A

1. Fig 1: Automatic Transmission Oil Pan Sub-Assembly Bolts Tightening Sequence

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly.
   2. Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.
   3. Temporarily install the automatic transmission oil pan sub-assembly to the automatic transmission case sub-assembly with the 13 bolts.
   4. Tighten the 13 bolts in the order shown in the illustration.

      Torque: 8.9 N.m (91 kgf/cm, 79 in.lbf) 

Torque: 50 N.m (510 kgf/cm, 37 ft.lbf) 

Torque: 29 N.m (296 kgf/cm, 21 ft.lbf) 

Refer to PROCEDURE - Step 88

Refer to PROCEDURE - Step 89

Refer to PROCEDURE - Step 90

Refer to PROCEDURE - Step 2

Refer to INITIALIZATION [12/2021 - ]