LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> LC 500 2D Convertible >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Door / Hatch - Service Information (Convertible) (1 Of 2) >> Front Door >> Disassembly [05/2023 - ] >> Procedure

Disassembly [05/2023 - ]: Procedure

  1. PRECAUTION 
    WARNING:

    Be sure to read Precaution thoroughly before servicing.

    GTY824211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Refer to PRECAUTION [05/2023 - ]

    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

    Refer to BEFORE DISCONNECTING BATTERY [05/2023 - ]

  2. REMOVE FRONT DOOR TRIM COVER SUB-ASSEMBLY LH (for Driver Side) 
    1. Grasp the end of the front door trim cover sub-assembly LH and front door trim board sub-assembly LH and while pulling back, detach the clip.
      GTY801528Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Detach the remaining clip and remove the front door trim cover sub-assembly LH.
      GTY786754Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE COURTESY LIGHT ASSEMBLY (for Driver Side) 

    Refer to PROCEDURE - Step 1

  4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Driver Side) 
    1. Remove the 2 screws.
      GTY829824Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Grasp the end of the front door trim board sub-assembly LH and front door inside panel sub-assembly LH and while pulling back, detach the clip.
      GTY821114Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Place your hands at the position shown in the illustration and pull to detach the clip.
      GTY775878Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    4. Place your hands at the position shown in the illustration and pull to detach the remaining clip, then lift up the front door trim board sub-assembly LH in the direction of the arrow and detach the guide.
      GTY953012Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
      Lift Up in this Direction
    5. Disconnect the connector.
      GTY951735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disconnect the front door open lever lock remote control cable from the front door inside handle sub-assembly LH and remove the front door trim board sub-assembly LH.
      GTY953309Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY RH (for Front Passenger Side) 
    1. Grasp the end of the front door assist grip assembly RH and front door trim board sub-assembly RH and while pulling back, detach the clip.
      GTY830087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Place your hands at the position shown in the illustration, detach the clip.
      GTY954086Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
    3. Place your hands at the position shown in the illustration, detach the remaining clip and remove the front door assist grip assembly RH.
      GTY953736Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
  6. REMOVE COURTESY LIGHT ASSEMBLY (for Front Passenger Side) 

    Refer to PROCEDURE - Step 1

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH (for Front Passenger Side) 
    1. Remove the 3 screws.
      GTY953294Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Grasp the end of the front door trim board sub-assembly RH and front door inside panel sub-assembly RH and while pulling back, detach the clip.
      GTY953852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Place your hands at the position shown in the illustration and lift up the front door trim board sub-assembly RH in the direction of the arrow and detach the guide.
      GTY953230Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    4. Disconnect the connector.
      GTY953298Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the front door open lever lock remote control cable from the front door inside handle sub-assembly RH and remove the front door trim board sub-assembly RH.
      GTY952962Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE NO. 1 SPEAKER WITH BOX ASSEMBLY 

    Refer to PROCEDURE - Step 5

  9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH 

    Refer to PROCEDURE - Step 6

  10. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH 
    1. Place your hands on the front door lower frame bracket garnish LH and pull to detach the clip and remove the front door lower frame bracket garnish LH.
      GTY953877Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
  11. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER LH 

    Refer to PROCEDURE - Step 8

  12. REMOVE FRONT DOOR DIVISION BAR SEAL LH 
    GTY953297Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a clip remover, remove the 2 clips and front door division bar seal LH.
  13. REMOVE FRONT DOOR NO. 3 WEATHERSTRIP LH 
    GTY786787Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a clip remover, remove the 3 clips and front door No. 3 weatherstrip LH.
  14. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH 

    Refer to PROCEDURE - Step 10

  15. REMOVE FRONT DOOR WEATHERSTRIP LH 
    GTY952923Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Remove in this Direction
    Double-sided Tape
    1. Using a clip remover, remove the 3 clips.
    2. Remove the double-sided tape.
    3. Detach the clip.
    4. Detach the hook and remove the front door weatherstrip LH as shown in the illustration.
    5. Clean the door panel.
  16. REMOVE FRONT DOOR TRIM SEAL LH 
    GTY952958Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the clip and remove the front door trim seal LH.
  17. REMOVE REAR ACCESS PANEL WEATHERSTRIP LH 
    GTY953554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Double-sided Tape
    1. Using a clip remover, remove the clip.
    2. Detach the clip.
    3. Remove the adhesional surface of the double-sided tape and rear access panel weatherstrip LH.
    4. Clean the door panel.
  18. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    1. Close the front door glass sub-assembly RH fully close position.
      1. Connect the connector.
        GTY952132Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Insert the upper portion of the front door trim board sub-assembly RH into the front door panel to temporarily set it.
        GTY952513Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Temporarily Set in this Direction
      3. Turn the engine switch to ON.
      4. for Driver Side:
        1. Operate the multiplex network master switch assembly and set the front door glass sub-assembly RH to the fully close position.
      5. for Front Passenger side:
        1. Operate the power window regulator switch assembly and set the front door glass sub-assembly LH to the fully close position.
      6. Turn the engine switch off.
      7. Lift up the front door trim board sub-assembly RH in the direction of the arrow and detach the guide.
        GTY952504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Remove in this Direction
      8. Disconnect the connector.
        GTY951735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) battery terminal.

      Refer to REMOVAL [05/2023 - ]

      WARNING:
      GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
      • If the airbag deploys for any reason, it may cause a serious accident.
  19. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side) 

    Refer to PROCEDURE - Step 3

  20. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) 

    Refer to PROCEDURE - Step 3

  21. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH 
    1. Remove the 4 screws and front door inside handle sub-assembly LH.
      GTY786747Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH 
    GTY829822Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Pull up the claw as shown in the illustration and remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH.
  23. REMOVE INDICATOR LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 5

  24. REMOVE INDICATOR LIGHT BRACKET 

    Refer to PROCEDURE - Step 6

  25. REMOVE INDICATOR LIGHT COVER 

    Refer to PROCEDURE - Step 7

  26. REMOVE SEAT MEMORY SWITCH (for Driver Side) 

    Refer to PROCEDURE - Step 3

  27. REMOVE NO. 2 FRONT DOOR WIRE LH 
    GTY786746Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the clamp.
    2. Disconnect the connector and remove the No. 2 front door wire LH.
  28. REMOVE FRONT DOOR MULTIPLEX NETWORK ECU LH 
    GTY789376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Screw
    Connector
    1. Disconnect the 3 connectors.
    2. Remove the 2 screws and front door multiplex network ECU LH.
  29. REMOVE NO. 1 FRONT DOOR HOLE COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 7

  30. REMOVE DOOR SIDE AIRBAG SENSOR LH 

    Refer to PROCEDURE - Step 8

  31. REMOVE FRONT DOOR INSIDE PANEL SUB-ASSEMBLY LH 
    1. Insert a hand into the service hole and detach the snap lock and remove the door lock side rod as shown in the illustration.
      GTY952199Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. GTY786781Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the bolt from the vehicle body.

    3. GTY786782Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the claw and disconnect the front door wire LH.

    4. Remove the grommet and disconnect the connector.
      GTY810039Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Grommet
      Connector
    5. Remove the 4 bolts.
      GTY954084Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      "TORX" screw
      Bolt
      "TORX" bolt
      (w/ Rubber Cushion)
    6. Using a T30 "TORX" socket wrench, remove the "TORX" bolt and 10 "TORX" screws.
    7. Detach the center door guide piece in the direction indicated by the arrow shown in the illustration and remove the front door inside panel sub-assembly LH together with the front door glass sub-assembly LH.
      NOTE:
      • Although CFRP material has high strength, there is a possibility of cracking if an excessive load is applied. As a result, pay attention to how it is handled.
      • Perform this operation with 2 or more people because of the risk of deformation or damage.
      • Be careful not to damage the front door glass sub-assembly LH.
      GTY953141Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  32. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH 

    Refer to PROCEDURE - Step 14

  33. INSTALL DOOR LOCK WIRING HARNESS SEAL 

    Refer to PROCEDURE - Step 15

  34. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 16

  35. REMOVE FRONT DOOR OPEN LEVER LOCK REMOTE CONTROL CABLE 

    Refer to PROCEDURE - Step 17

  36. REMOVE FRONT DOOR LOCK / UNLOCK KNOB INSIDE LOCKING CABLE 

    Refer to PROCEDURE - Step 18

  37. REMOVE FRONT DOOR CHECK ASSEMBLY LH 
    GTY829829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 nuts and front door check assembly LH.
  38. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH 
    1. Remove the 5 hole plugs.
      GTY786777Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 3 nuts.
      GTY786778Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Loosen the 2 nuts and remove the window regulator shims.
      GTY786780Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Record the number of window regulator shims removed.

    4. Lift up the glass in the direction shown in the illustration, loosen the bolt and remove the door glass female stabilizer LH and bolt.
      GTY827455Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Remove the 2 bolts.
      GTY829828Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Pull out the front door upper glass stop of the front door glass sub-assembly LH from the front door upper window stop, slide the front and rear of the front door glass sub-assembly LH in the direction indicated by the arrows shown in the illustration to remove the front door glass sub-assembly LH.
      GTY831243Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
      NOTE:

      Do not damage the front door glass sub-assembly LH.

  39. REMOVE FRONT DOOR UPPER WINDOW STOP 
    1. Remove the 2 front door upper window stops.
  40. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH 
    1. Remove the 2 nuts and front door front lower frame sub-assembly LH.
      GTY786805Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  41. REMOVE FRONT DOOR GLASS RUN LH 
    1. Remove the front door glass run LH from the front door front lower frame sub-assembly LH.
  42. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH 
    1. Disconnect the connector and remove the 3 nuts.
      GTY833490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Nut
      Connector
    2. Remove the 4 nuts and front door window regulator sub-assembly LH.
      GTY953005Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Measure the stud bolt (A) at the bottom of the front door window regulator sub-assembly LH and record its dimensions.
  43. REMOVE FRONT DOOR WIRE LH 
    1. Detach the clamp and remove the front door wire LH.
      GTY1242625Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  44. REMOVE HOLE PLUG 
    1. for Front Door Inside Panel Side:

      Remove the 2 hole plugs.

      GTY785122Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for Front Door Outer Panel Side:

      Remove the hole plug.

      GTY786808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. REMOVE FRONT DOOR PANEL CUSHION 
    1. Detach the claw and remove the front door panel cushion.
      GTY829466Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. INSTALL FRONT DOOR DUST PROOF SEAL 
    1. Detach the claw and guide to remove the front door dust proof seal.
      GTY953494Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  47. REMOVE OUTSIDE DOOR HANDLE SUB-ASSEMBLY LH 
    1. Apply protective tape to the handle and door outer panel of the outside door handle sub-assembly LH to prevent damage.
      GTY817064Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Detach the clamp and disconnect the 4 connectors.
      GTY802668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Connector
    3. Remove the 4 bolts and outside door handle sub-assembly LH.
  48. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH 
    1. GTY786800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using a T30 "TORX" socket wrench, remove the "TORX" screw.

    2. Put the outside door handle in the full stroke position and remove the front door lock cylinder assembly LH.
      GTY814934Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  49. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH 
    1. Detach the grommet and adhesional surface of the double-sided tape.
      GTY952889Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Grommet
      Double-sided Tape
    2. Using a clip remover, detach the clip and remove the front door No. 2 weatherstrip LH.
    3. Clean the door panel.
  50. REMOVE STEP PANEL WIRE LH 
    1. Detach the clamp and remove the step panel wire LH.
      GTY786802Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals