LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> ES 250 Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge / Display - Service Information >> Combination Meter >> Installation [08/2021 - ] >> Procedure

Installation [08/2021 - ]: Procedure

  1. INSTALL COMBINATION METER ASSEMBLY 
    1. Connect the 2 connectors.
    2. Engage the clamp.
    3. Install the combination meter assembly with the 4 screws.
  2. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 
    1. Engage the 3 guides and 12 claws as shown in the illustration.
      GTY1087752Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction - -
    2. Install the 2 screws.
    3. Connect the connector.
    4. Engage the 2 guides and 4 clips as shown in the illustration to install the instrument cluster finish panel assembly.
      GTY816782Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  3. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH 

    Refer to PROCEDURE - Step 17

  4. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19

  5. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH 

    Refer to PROCEDURE - Step 22

  6. INSTALL MULTI-DISPLAY ASSEMBLY WITH CLOCK (for 8 Inch Display) 

    Refer to PROCEDURE - Step 3

  7. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 8 Inch Display) 

    Refer to PROCEDURE - Step 24

  8. INSTALL MULTI-DISPLAY ASSEMBLY WITH CLOCK (for 12.3 Inch Display) 

    Refer to PROCEDURE - Step 5

  9. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 12.3 Inch Display) 

    Refer to PROCEDURE - Step 26

  10. INSTALL AIR CONDITIONING CONTROL ASSEMBLY 

    Refer to PROCEDURE - Step 1

  11. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Headup Display) 

    Refer to PROCEDURE - Step 28

  12. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Headup Display) 

    Refer to PROCEDURE - Step 29

  13. INSTALL NO. 2 INSTRUMENT CLUSTER MOULDING 

    Refer to PROCEDURE - Step 30

  14. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 33

  15. INSTALL INSTRUMENT SIDE PANEL RH 

    Refer to PROCEDURE - Step 37

  16. INSTALL FRONT DOOR OPENING TRIM COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  17. INSTALL COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  18. INSTALL FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 43

  20. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 44

  21. INSTALL INSTRUMENT SIDE PANEL LH 

    Refer to PROCEDURE - Step 45

  22. INSTALL FRONT DOOR OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 31

  23. INSTALL COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 32

  24. INSTALL FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 33

  25. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column) 

    Refer to PROCEDURE - Step 17 [06/2018 - 09/2022] , or refer to PROCEDURE - Step 17 [09/2022 - ]

scientia non olet · About LEMON Manuals