LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2022 >> ES 250 Base >> Repair and Diagnosis >> Electrical >> Gauges >> Interior Body Panels - Service Information (1 Of 2) >> Instrument Panel Safety Pad >> Installation [08/2021 - ] >> Procedure

Installation [08/2021 - ]: Procedure

  1. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 
    1. Engage the 5 guides as shown in the illustration to temporarily install the instrument panel safety pad sub-assembly.
      GTY1085655Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction - -
      NOTE:
      • Do not damage the instrument panel safety pad sub-assembly.
      • Do not allow the wire harnesses to interfere with the surrounding parts.
    2. Install the 5 bolts <B>, 2 clips and nut <D>.
    3. Install the instrument panel safety pad sub-assembly with the 2 bolts <A>.

      Bolt<A> 

      Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

    4. Engage each clamp.
    5. Connect each connector.
    6. Engage the 2 claws to connect the cooler (room temp. sensor) thermistor.
  2. CONNECT INSTRUMENT PANEL WIRE 

    Refer to PROCEDURE - Step 3

  3. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Engage the 4 claws as shown in the illustration to install the No. 3 instrument panel register assembly.
      GTY1085579Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  4. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH 
    1. w/ Ambient Light:
      1. Connect the connector.
    2. Engage the 6 clips as shown in the illustration to install the No. 2 instrument cluster finish panel garnish.
      GTY1085689Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  5. INSTALL SWITCH BASE 
    1. Connect the connector.
    2. Engage the 4 claws as shown in the illustration to install the switch base.
      GTY1085796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  6. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Connect the connector.
    2. Engage the clip and 3 claws as shown in the illustration to install the No. 2 instrument panel register assembly.
      GTY1085904Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  7. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET (w/ Manual (SOS) Switch) 

    Refer to PROCEDURE - Step 4 [08/2020 - 09/2022] , or refer to PROCEDURE - Step 4 [09/2022 - ]

  8. INSTALL RADIO RECEIVER ASSEMBLY WITH SWITCH 

    Refer to PROCEDURE - Step 7 [08/2020 - 09/2022] , or refer to PROCEDURE - Step 5 [09/2022 - ]

  9. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) 

    Refer to PROCEDURE - Step 4

  10. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 
    1. Engage the 3 guides and 3 claws as shown in the illustration to install the No. 2 instrument panel speaker panel sub-assembly.
      GTY783079Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
  11. INSTALL FRONT PILLAR GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 30

  12. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) 

    Refer to PROCEDURE - Step 4

  13. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 
    1. Engage the 2 guides and 3 claws as shown in the illustration to install the No. 1 instrument panel speaker panel sub-assembly.
      GTY1085976Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
  14. INSTALL FRONT PILLAR GARNISH ASSEMBLY LH 

    Refer to PROCEDURE - Step 30

  15. INSTALL COMBINATION METER ASSEMBLY 

    Refer to PROCEDURE - Step 1

  16. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 
    1. Engage the 3 guides and 12 claws as shown in the illustration.
      GTY1085492Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction - -
    2. Install the instrument cluster finish panel assembly with the 2 screws <C>.
    3. Connect the connector.
  17. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH 
    1. Engage the 2 clips as shown in the illustration to install the No. 1 instrument cluster finish panel garnish.
      GTY1085647Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  18. INSTALL CENTER INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY 
    1. Install the center instrument panel reinforcement sub-assembly with the bolt <B> and 2 nuts <D>.
    2. Engage the 2 clamps.
  19. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 
    1. Engage the 4 guides and 6 clips to install the upper instrument panel finish panel sub-assembly as shown in the illustration.
      GTY1085800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
  20. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY 

    Refer to PROCEDURE - Step 1

  21. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY 
    1. Connect the connector.
    2. Engage the 2 guides and 4 clips to install the No. 1 speaker opening cover assembly as shown in the illustration.
      GTY1086103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  22. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH 
    1. Engage the claw and 7 clips to install the No. 3 instrument cluster finish panel garnish as shown in the illustration.
      GTY1085272Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  23. INSTALL MULTI-DISPLAY ASSEMBLY WITH CLOCK (for 8 Inch Display) 

    Refer to PROCEDURE - Step 3

  24. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 8 Inch Display) 
    1. Engage the 4 guides and 7 clips to install the instrument panel finish panel sub-assembly as shown in the illustration.
      GTY1086041Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  25. INSTALL MULTI-DISPLAY ASSEMBLY WITH CLOCK (for 12.3 Inch Display) 

    Refer to PROCEDURE - Step 5

  26. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 12.3 Inch Display) 
    1. Engage the 4 guides and 7 clips to install the instrument panel finish panel sub-assembly as shown in the illustration.
      GTY1085419Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  27. INSTALL AIR CONDITIONING CONTROL ASSEMBLY 

    Refer to PROCEDURE - Step 1

  28. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Headup Display) 
    1. Engage the 8 guides, claw and 2 clips as shown in the illustration to install the instrument cluster finish panel sub-assembly.
      GTY1086084Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  29. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Headup Display) 
    1. Engage the 7 guides, claw and 2 clips as shown in the illustration to install the instrument cluster finish panel sub-assembly.
      GTY1085685Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  30. INSTALL NO. 2 INSTRUMENT CLUSTER MOULDING 
    1. Engage the guide and 5 clips as shown in the illustration to install the No. 2 instrument cluster moulding.
      GTY1085899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  31. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY 
    1. Connect each connector.
    2. Engage the 6 claws as shown in the illustration.
      GTY1085201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
    3. Install the glove compartment door assembly with the 5 screws <C>.
  32. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 1

  33. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY 
    1. Engage the 7 claws and 11 clips as shown in the illustration to install the lower instrument panel sub-assembly.
      GTY1085557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction - -
  34. INSTALL LOWER INSTRUMENT PANEL LH 
    1. Engage the guide, 2 clips and 2 claws as shown in the illustration to install the lower instrument panel LH.
      GTY782930Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  35. INSTALL LOWER INSTRUMENT FINISH SUB PANEL 
    1. Engage the clip and claw as shown in the illustration to install the lower instrument finish sub panel.
      GTY823545Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  36. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
    1. Connect the connector.
    2. Engage the clamp.
    3. Engage the 4 guides and 7 claws as shown in the illustration to install the No. 2 instrument panel under cover sub-assembly.
      GTY807956Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
  37. INSTALL INSTRUMENT SIDE PANEL RH 
    1. Engage the 2 guides and 6 claws as shown in the illustration to install the instrument side panel RH.
      GTY1085741Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
  38. INSTALL FRONT DOOR OPENING TRIM COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 31

  39. INSTALL COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 32

  40. INSTALL FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 33

  41. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 1

  42. INSTALL LOWER INSTRUMENT PANEL 
    1. Connect the connector.
    2. Engage the 3 guides and 4 clips as shown in the illustration to install the lower instrument panel.
      GTY806068Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
  43. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 
    1. Connect each connector.
    2. Engage each clamp.
    3. Engage the guide, 4 claws and 3 clips as shown in the illustration.
      GTY1085797Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
    4. Install the No. 1 instrument panel sub-assembly with the screw <C>.
    5. Engage the 2 claws.
    6. Engage the 2 guides and claw.
  44. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
    1. Connect the connector and engage the 2 clamps.
    2. Engage the 2 claws to connect the DLC3 connector.
    3. Engage the 2 guides and 2 claws as shown in the illustration.
      GTY827445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
    4. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <C>.
  45. INSTALL INSTRUMENT SIDE PANEL LH 
    1. Engage the 2 guides and 6 claws as shown in the illustration to install the instrument side panel LH.
      GTY1085847Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction (1)
      Install in this Direction (2)
  46. INSTALL FRONT DOOR OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 31

  47. INSTALL COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 32

  48. INSTALL FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 33

  49. INSTALL REAR CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [08/2020 - 09/2022] , or refer to INSTALLATION [09/2022 - ]

  50. INSTALL TURN SIGNAL SWITCH 

    Refer to PROCEDURE - Step 1

  51. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY 

    Refer to PROCEDURE - Step 1

  52. INSTALL UPPER STEERING COLUMN COVER 

    for Manual Tilt and Manual Telescopic Steering Column: Refer to PROCEDURE - Step 10 [06/2018 - 09/2022] , or refer to PROCEDURE - Step 10 [09/2022 - ]

    for Power Tilt and Power Telescopic Steering Column: Refer to PROCEDURE - Step 10 [06/2018 - 09/2022] , or refer to PROCEDURE - Step 10 [09/2022 - ]

  53. INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY 

    for Manual Tilt and Manual Telescopic Steering Column: Refer to PROCEDURE - Step 11 [06/2018 - 09/2022] , or refer to PROCEDURE - Step 11 [09/2022 - ]

    for Power Tilt and Power Telescopic Steering Column: Refer to PROCEDURE - Step 11 [06/2018 - 09/2022] , or refer to PROCEDURE - Step 11 [09/2022 - ]

  54. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 
  55. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9 [08/2020 - 09/2022] , or refer to PROCEDURE - Step 9 [09/2022 - ]

  56. INSTALL STEERING WHEEL ASSEMBLY 

    Refer to PROCEDURE - Step 8

  57. CHECK STEERING WHEEL CENTER POINT 
  58. INSTALL HORN BUTTON ASSEMBLY 

    Refer to INSTALLATION [08/2020 - ]

  59. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column) 

    Refer to PROCEDURE - Step 17 [06/2018 - 09/2022] , or refer to PROCEDURE - Step 17 [09/2022 - ]

scientia non olet · About LEMON Manuals