Replacement [10/2018 - 07/2022]: Procedure

Refer to PROCEDURE - Step 7 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 7 [08/2021 - 07/2022]

Refer to PROCEDURE - Step 8 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 8 [08/2021 - 07/2022]

Refer to PROCEDURE - Step 9 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 9 [08/2021 - 07/2022]

1. Remove the refill plug and gasket from the rear transaxle case sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle case sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	No. 1 Transmission Oil Filler Tube

   HINT: 

   Removing the No. 1 transmission oil filler tube will drain all oil in the continuously variable transaxle assembly.

4. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle case sub-assembly.

   Torque: 0.8 N.m (8 kgf/cm, 7 in.lbf) 

5. Using a 10 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle case sub-assembly.

   HINT: 

   Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.

6. Temporarily install the gasket and refill plug to the continuously variable transaxle assembly.

   HINT: 

   Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.

Refer to REMOVAL [10/2018 - 07/2022]

1. Using SST, remove the front drive shaft oil seal LH from the continuously variable transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09308-00010 
   NOTE:

   Do not damage the continuously variable transaxle assembly.

1. Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09308-00010 
   NOTE:

   Do not damage the continuously variable transaxle assembly.

1. Using SST and a hammer, install a new front drive shaft oil seal LH to the continuously variable transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09649-17010 
   • SST: 09950-70010 
     1. 09951-07150

   Standard Depth

   -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

   NOTE:

   • Be sure to install the front drive shaft oil seal LH in the correct direction.
   • Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.
   • Do not damage the lip of the front drive shaft oil seal LH.

1. Using SST and a hammer, install a new front drive shaft oil seal RH to the continuously variable transaxle assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09316-10010 
   • SST: 09950-70010 
     1. 09951-07150

   Standard Depth

   -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

   NOTE:

   • Be sure to install the front drive shaft oil seal RH in the correct direction.
   • Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.
   • Do not damage the lip of the front drive shaft oil seal RH.

Refer to INSTALLATION [10/2018 - 07/2022]

Refer to ADJUSTMENT [10/2018 - 10/2019] , or refer to ADJUSTMENT [10/2019 - 07/2022]

Refer to PROCEDURE - Step 58 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 58 [08/2021 - 07/2022]

Refer to PROCEDURE - Step 59 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 59 [08/2021 - 07/2022]

Refer to PROCEDURE - Step 60 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 60 [08/2021 - 07/2022]