LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 43 (Hybrid Battery Control System (Service Information) (2 Of 2)) >> Fuse Box >> Installation [10/2018 - ] >> Procedure

Installation [10/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus UX 250h, 2023 Lexus UX 250h, 2022 Lexus UX 250h, 2021 Lexus UX 250h, and 2020 Lexus UX 250h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL HYBRID BATTERY TERMINAL BLOCK 
    WARNING:

    Be sure to wear insulated gloves and protective goggles.

    1. Connect the 2 hybrid battery terminal block connectors.
      NOTE:

      Make sure that the connectors are connected securely.

    2. Install the hybrid battery terminal block to the HV battery with the bolt.
      GTY549850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin

      Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf) 

      NOTE:

      Make sure to align the hole of the hybrid battery terminal block with the pin.

  2. INSTALL NO. 1 HV BATTERY SHIELD PANEL 

    Refer to PROCEDURE - Step 2

  3. INSTALL UPPER HV BATTERY COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  4. CONNECT FLOOR WIRE 

    See step  10

  5. INSTALL NO. 1 HV BATTERY PROTECTOR 

    See step  11

  6. CONNECT FLOOR WIRE 

    See step  12

  7. CONNECT FLOOR UNDER WIRE 

    See step  13

  8. INSTALL NO. 1 HV BATTERY COVER PANEL RH 

    See step  14

  9. INSTALL BATTERY COOLING BLOWER ASSEMBLY 

    See step  1

  10. INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY 

    See step  16

  11. INSTALL REAR UNDER COVER 

    See step  17

  12. INSTALL REAR UNDER SIDE COVER LH 

    Refer to PROCEDURE - Step 40 [10/2018 - 10/2020] Refer to PROCEDURE - Step 40 [10/2020 - 07/2022] Refer to PROCEDURE - Step 40 [07/2022 - ]

  13. INSTALL REAR DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 42 [10/2018 - 10/2020] Refer to PROCEDURE - Step 42 [10/2018 - 10/2020] Refer to PROCEDURE - Step 42 [07/2022 - ]

  14. INSTALL REAR UNDER SIDE COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 41 [10/2018 - 10/2020] Refer to PROCEDURE - Step 41 [10/2020 - 07/2022] Refer to PROCEDURE - Step 41 [07/2022 - ]

  15. INSTALL REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 43 [10/2018 - 10/2020] Refer to PROCEDURE - Step 43 [10/2020 - 07/2022] Refer to PROCEDURE - Step 43 [07/2022 - ]

  16. INSTALL REAR SEAT CUSHION LOCK HOOK 

    Refer to PROCEDURE - Step 1 [10/2018 - 07/2022] Refer to PROCEDURE - Step 1 [07/2022 - ]

  17. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY 

    Refer to PROCEDURE - Step 5 Refer to PROCEDURE - Step 4

  18. INSTALL SERVICE PLUG GRIP 

    Refer to INSTALLATION [10/2018 - ] 

  19. PERFORM HIGH VOLTAGE FUSE ACCUMULATED LOAD HISTORY RESET 

    Refer to UTILITY [10/2018 - ]

scientia non olet · About LEMON Manuals