Installation [10/2018 - 07/2022]: Procedure

INSTALL REAR SEAT CUSHION LOCK HOOK

Engage the claws to install a new rear seat cushion lock hook as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

INSTALL REAR SEATBACK ASSEMBLY LH

Place the rear seatback assembly LH in the cabin.
NOTE:
Be careful not to damage the vehicle body.
Engage the guides to install the rear seatback assembly LH.

Fig 1: Rear Seat Tightening Sequence
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Install the 2 bolts.
Torque: 36.8 N.m (375 kgf/cm, 27 ft.lbf)

NOTE:
Tighten bolts in the order shown in the illustration.

Engage the hook and loop fasteners.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Hook and Loop Fastener

Install the clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL REAR SEATBACK ASSEMBLY RH

Place the rear seatback assembly RH in the cabin.
NOTE:
Be careful not to damage the vehicle body.
Engage the guides to install the rear seatback assembly RH.

Fig 2: Rear Seat Tightening Sequence
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Install the 2 bolts.
Torque: 36.8 N.m (375 kgf/cm, 27 ft.lbf)

NOTE:
Tighten bolts in the order shown in the illustration.

Engage the hook and loop fasteners.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Hook and Loop Fastener

Install the clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Place the bench type rear seat cushion assembly in the cabin.
NOTE:
Be careful not to damage the vehicle body.

Pass the rear center seat outer belt assembly through the bench type rear seat cushion assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the rear center seat outer belt assembly with the nut.
Torque: 42 N.m (428 kgf/cm, 31 ft.lbf)

Engage the rear seat cushion frame hook on the rear side of the bench type rear seat cushion assembly as shown in the illustration.

*a	Rear Seat Cushion Frame Hook Front Side
*b	Rear Seat Cushion Frame Hook Rear Side
	Install in this Direction (1)
	Install in this Direction (2)

Engage the rear seat cushion frame hooks on the front side of the bench type rear seat cushion assembly as shown in the illustration.
NOTE:
Confirm that the bench type rear seat cushion assembly is securely installed.

INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for HV Model)

Place the bench type rear seat cushion assembly in the cabin.
NOTE:
Be careful not to damage the vehicle body.

Pass the rear center seat outer belt assembly through the bench type rear seat cushion assembly.

Install the rear center seat outer belt assembly with the nut.
Torque: 42 N.m (428 kgf/cm, 31 ft.lbf)

Engage the rear seat cushion frame hook on the rear side of the bench type rear seat cushion assembly as shown in the illustration.

*a	Rear Seat Cushion Frame Hook Front Side
*b	Rear Seat Cushion Frame Hook Rear Side
	Install in this Direction (1)
	Install in this Direction (2)

Engage the rear seat cushion frame hooks on the front side of the bench type rear seat cushion assembly as shown in the illustration.
NOTE:
Confirm that the bench type rear seat cushion assembly is securely installed.

INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (for RH Side)
1. Install the rear seat center headrest assembly.
INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)
1. Install the rear seat headrest assembly.
INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)
1. Install the rear seat headrest assembly.
INSTALL DECK BOARD ASSEMBLY (w/o Deck Floor Box)
Refer to PROCEDURE - Step 67 [10/2018 - 10/2020] , or refer to PROCEDURE - Step 67 [10/2020 - 07/2022]