LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 22 (Fuel System (M20A-FXS) (Service Information)) >> Fuel Pump >> Removal [10/2018 - 07/2022] >> Procedure

Removal [10/2018 - 07/2022]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus UX 250h, 2023 Lexus UX 250h, 2022 Lexus UX 250h, 2021 Lexus UX 250h, and 2020 Lexus UX 250h. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [10/2018 - 07/2022]

  2. DISCHARGE FUEL SYSTEM PRESSURE 

    Refer to PRECAUTION [10/2018 - ]

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 

    Refer to PROCEDURE - Step 5

  4. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [10/2018 - 07/2022]

  5. REMOVE REAR FLOOR SERVICE HOLE COVER 
    1. Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.
      GTY783212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
    2. Disconnect the 2 fuel suction tube with pump and gauge assembly connectors.
      GTY809223Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE FUEL TANK PRESSURE SENSOR (VAPOR PRESSURE SENSOR ASSEMBLY) 

    Refer to PROCEDURE - Step 3

  7. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY 
    1. Disconnect the fuel tank vent hose sub-assembly from the fuel suction tube with pump and gauge assembly.
      GTY779324Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to PRECAUTION [10/2018 - ]

  8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY 
    1. Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
      GTY826105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Plate Sub-assembly
      *2 Tube Joint Clip
      *3 Fuel Tank Main Tube Sub-assembly
      *4 Fuel Tube Joint
      *5 O-ring
      *a Nylon Tube
      Pull off
      Pull off
      NOTE:
      • Remove any foreign matter on the fuel tube joint before performing this work.
      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
      • Be sure to disconnect the fuel tube joint by hand.
      • Do not bend, twist, pinch or kink the nylon tube.
      • Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
      • If the fuel tube joint and plate sub-assembly are stuck, push and pull to release them.
  9. REMOVE FUEL PUMP GAUGE RETAINER 
    1. Disengage the 2 claw to remove the No. 1 fuel tube clamp.
      GTY809079Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the fuel pump gauge retainer.
      1. Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
        • SST: 09808-01071 
        • SST: 09808-14031 
          1. 09808-01030
          2. 09808-01090

        HINT: 

        Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.

        GTY796329Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Insertion Point
        *b SST (Plate)
        *c SST (Claw)
        *d SST (Bolt)
      2. While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
      3. Install SST (handle) to SST (plate).
        GTY808541Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a SST (Handle)
        *b SST (Plate)
        *c SST (Claw)
        *d SST (Bolt)
        • SST: 09808-01071 
        • SST: 09808-14031 
          1. 09808-01010
          2. 09808-01030
          3. 09808-01090
      4. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.
        NOTE:
        • Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.
        • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
        • Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
        • Do not spin SST too fast or use an impact wrench as this may result in damage to components.
        • If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
      5. While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.
  10. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 
    1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.
      NOTE:

      Be careful not to bend the arm of the fuel sender gauge assembly.

    2. Remove the fuel suction tube set gasket from the fuel tank assembly.
      GTY779326Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals