LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> RX 450h Base >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Exterior Panels / Trim - Service Information (1 Of 2) >> Front Bumper >> Disassembly [08/2019 - ] >> Procedure

Disassembly [08/2019 - ]: Procedure

  1. REMOVE FRONT BUMPER ARM HOLE COVER LH 
    1. Remove the screw and clip.
      GTY950741Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Screw
      Clip
    2. Disengage the 3 guides to remove the front bumper arm hole cover LH.
      GTY951288Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE FRONT BUMPER HOLE COVER ASSEMBLY LH (w/o Fog Light) 
    1. w/ Headlight Cleaner System:
      1. Disengage the clamp.
        GTY951371Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the clip.
      GTY950974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Clip
      Screw
    3. Remove the 2 screws and front bumper hole cover assembly LH.
  3. REMOVE FRONT BUMPER HOLE COVER ASSEMBLY RH (w/o Fog Light) 

    HINT: 

    Use the same procedure as for the LH side.

  4. REMOVE CONNECTOR COVER (w/o Fog Light) 

    HINT: 

    Use the same procedure for all connector covers.

    1. Disengage the clamp to remove the connector cover.
      GTY951369Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light) 

    Refer to PROCEDURE - Step 3

  6. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light) 

    HINT: 

    Use the same procedure as for the LH side.

  7. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY 

    Refer to PROCEDURE - Step 2

  8. REMOVE TELEVISION CAMERA WIRE (w/ Panoramic View Monitor System) 
    1. Disconnect the connector to remove the television camera wire.
      GTY962960Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System) 

    Refer to PROCEDURE - Step 4

  10. REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System) 

    Refer to PROCEDURE - Step 2

  11. REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System) 

    Refer to PROCEDURE - Step 3

  12. REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System) 

    Refer to PROCEDURE - Step 4

  13. REMOVE NO. 4 ENGINE ROOM WIRE (w/ Intuitive Parking Assist System) 
    1. Disengage the 12 clamps to remove the No. 4 engine room wire.
      GTY951287Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE ULTRASONIC SENSOR CLIP (w/ Intuitive Parking Assist System) 

    HINT: 

    • Use the same procedure for all ultrasonic sensor clips.
    • When removing the ultrasonic sensor clip, heat the front bumper assembly and ultrasonic sensor clip using a heat light.

    Heating Temperature

    Item Temperature
    Ultrasonic Sensor Clip and Front Bumper Assembly 20 to 30°C (68 to 86°F)
    WARNING:
    • Do not touch the heat light and heated parts, touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat the front bumper assembly or ultrasonic sensor clip excessively.

    1. Using a heat light, heat the front bumper assembly and ultrasonic sensor clip.
    2. Remove the ultrasonic sensor clip.
      GTY950004Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System) 

    Refer to PROCEDURE - Step 1

  16. REMOVE HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System) 

    HINT: 

    Use the same procedure as for the LH side.

  17. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System) 

    Refer to PROCEDURE - Step 4

  18. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System) 

    HINT: 

    Use the same procedure as for the LH side.

  19. REMOVE HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System) 
    1. Disengage the 8 clamps and remove the headlight cleaner hose.
      GTY951286Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE NO. 2 WASHER BRACKET (w/ Headlight Cleaner System) 

    HINT: 

    When removing the No. 2 washer bracket, heat the No. 2 washer bracket and front bumper assembly using a heat light.

    Heating Temperature

    Item Temperature
    No. 2 Washer Bracket and Front Bumper Assembly 20 to 30°C (68 to 86°F)
    WARNING:
    • Do not touch the heat light and heated parts, touching the heat light may result in burns.
    • Touching heated parts for a long time may result in burns.
    GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Heated Part
    *b Heat Light
    NOTE:

    Do not heat the No. 2 washer bracket or front bumper assembly excessively.

    1. Using a heat light, heat the No. 2 washer bracket and front bumper assembly.
    2. Remove the No. 2 washer bracket.
      GTY951285Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE NO. 1 WASHER BRACKET (w/ Headlight Cleaner System) 

    HINT: 

    Use the same procedure for the No. 2 washer bracket.

  22. REMOVE NO. 1 MOULDING TAPE 
    1. Remove the No. 1 moulding tape.

      HINT: 

      Use the same procedure for the RH side and LH side.

      GTY951284Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE FRONT BUMPER HOLE COVER LH (except F-Sport) 
    1. Disengage the 5 claws.
      GTY950073Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Hook
    2. Disengage the hook to remove the front bumper hole cover LH.
  24. REMOVE FRONT BUMPER HOLE COVER LH (for F-Sport) 
    1. Disengage the 3 claws.
      GTY950397Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Hook
    2. Disengage the hook to remove the front bumper hole cover LH.
  25. REMOVE FRONT BUMPER HOLE COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  26. REMOVE LOWER SIDE RADIATOR GRILLE LH (except F-Sport) 
    1. Disengage the 5 claws to remove the lower side radiator grille LH.
      GTY951314Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE LOWER SIDE RADIATOR GRILLE LH (for F-Sport) 
    1. Remove the 4 clips.
      GTY951311Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 3 claws to remove the lower side radiator grille LH.
  28. REMOVE LOWER SIDE RADIATOR GRILLE RH 

    HINT: 

    Use the same procedure as for the LH side.

  29. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (except F-Sport) 
    1. Remove the 2 screws.
      GTY951310Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws to remove the front bumper extension mounting bracket as shown in the illustration.
      GTY951213Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  30. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (for F-Sport) 
    1. Remove the 2 screws.
      GTY951306Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws to remove the front bumper extension mounting bracket as shown in the illustration.
      GTY950071Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  31. REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM 
    1. Remove the 2 screws.
      GTY951325Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the claw and guide as shown in the illustration to remove the radiator grille (or front panel) emblem.
      GTY950048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  32. REMOVE HOOD TO RADIATOR GRILLE SEAL 
    1. Disengage the 18 clips to remove the hood to radiator grille seal.
      GTY951243Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE INNER RADIATOR GRILLE 
    1. Remove the 7 screws and 2 clips.
      GTY951377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Screw Clip
    2. Disengage the 3 claws and 7 guides to remove the inner radiator grille.
      GTY951238Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. REMOVE RADIATOR GRILLE SUB-ASSEMBLY 
    1. Remove the 2 clips and 12 screws.
      GTY951237Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 10 clips and 10 guides to remove the radiator grille sub-assembly.
      GTY951236Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE NO. 1 RADIATOR GRILLE MOULDING 
    1. Remove the 2 screws.
      GTY951235Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 10 claws and 2 clips to remove the No. 1 radiator grille moulding.
      GTY951312Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. REMOVE NO. 2 RADIATOR GRILLE MOULDING 
    1. Remove the screw.
      GTY951271Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 7 clips to remove the No. 2 radiator grille moulding.
  37. REMOVE FRONT BUMPER GUARD COVER LH (except F-Sport) 
    1. Remove the 3 screws and clip.
      GTY950716Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Screw
      Clip
    2. Remove the 2 clips.
      GTY951266Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 4 claws and 3 guides to remove the front bumper guard cover LH.
      GTY951265Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. REMOVE FRONT BUMPER GUARD COVER RH (except F-Sport) 

    HINT: 

    Use the same procedure as for the LH side.

  39. REMOVE FRONT BUMPER GUARD (except F-Sport) 
    1. Remove the 4 clips.
      GTY951263Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 6 claws and 4 guides to remove the front bumper guard.
      GTY951262Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. REMOVE FRONT BUMPER SIDE MOULDING LH (for F-Sport) 
    1. Remove the 2 screws.
      GTY951261Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws to remove the front bumper side moulding LH.
  41. REMOVE FRONT BUMPER SIDE MOULDING RH (for F-Sport) 

    HINT: 

    Use the same procedure as for the LH side.

  42. REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY (for F-Sport) 
    1. Remove the 2 screws and 2 clips.
      GTY950424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Screw Clip
    2. Remove the 8 clips.
      GTY951258Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 10 claws and 8 guides to remove the front bumper extension sub-assembly.
      GTY951257Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  43. REMOVE FRONT BUMPER ENERGY ABSORBER 
    1. Remove the front bumper energy absorber as shown in the illustration.
      GTY950538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  44. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY 
    1. Disengage the 3 clamps.
      GTY952820Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 clips.
      GTY952818Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 6 bolts and front bumper reinforcement sub-assembly.
      GTY952817Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. REMOVE FRONT BUMPER SIDE RETAINER LH 
    1. Remove the bolt.
      GTY659017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clip as shown in the illustration.
      GTY668884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
    3. Disengage the claw as shown in the illustration to remove the front bumper side retainer LH.
  46. REMOVE FRONT BUMPER SIDE RETAINER RH 

    HINT: 

    Use the same procedure as for the LH side.

scientia non olet · About LEMON Manuals