LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> RX 450h Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System (Service Information) >> Combination Meter >> Installation [10/2015 - 03/2018] >> Procedure

Installation [10/2015 - 03/2018]: Procedure

  1. INSTALL COMBINATION METER ASSEMBLY 
    1. Connect each connector.
    2. Engage the clamp.
    3. Install the combination meter assembly with the 4 screws.
  2. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Connect the connector.
    2. Engage the 7 clips as shown in the illustration.
      GTY652974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
    3. Engage the 4 clips and 2 claws to install the instrument cluster finish panel sub-assembly.
  3. INSTALL LOWER INSTRUMENT FINISH PANEL SUB 

    Refer to PROCEDURE - Step 32 [10/2015 - 12/2017] Refer to PROCEDURE - Step 32 [12/2017 - 03/2018]

  4. INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT 

    Refer to PROCEDURE - Step 6 [10/2015 - 12/2017] Refer to PROCEDURE - Step 5 [12/2017 - 08/2019]

  5. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 8 [10/2015 - 12/2017] Refer to PROCEDURE - Step 7 [12/2017 - 08/2019]

  6. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 9 [10/2015 - 12/2017] Refer to PROCEDURE - Step 8 [12/2017 - 08/2019]

  7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 33 [10/2015 - 12/2017] Refer to PROCEDURE - Step 33 [12/2017 - 03/2018]

  8. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 34 [10/2015 - 12/2017] Refer to PROCEDURE - Step 34 [12/2017 - 03/2018]

  9. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 35 [10/2015 - 12/2017] Refer to PROCEDURE - Step 35 [12/2017 - 03/2018]

  10. INSTALL COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 2

  11. INSTALL FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 43 [10/2015 - 12/2017] Refer to PROCEDURE - Step 42 [12/2017 - ]

  12. INSTALL INSTRUMENT PANEL GARNISH LH 

    Refer to PROCEDURE - Step 38 [10/2015 - 12/2017] Refer to PROCEDURE - Step 38 [12/2017 - 03/2018]

  13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 2

  14. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM 

    Refer to CUSTOMIZE PARAMETERS [10/2015 - ]

  15. INSTALL REAR DECK FLOOR BOX 

    Refer to PROCEDURE - Step 54 [10/2015 - 12/2017] Refer to PROCEDURE - Step 53 [12/2017 - ]

  16. INSTALL DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 56 [10/2015 - 12/2017] Refer to PROCEDURE - Step 55 [12/2017 - ]

scientia non olet · About LEMON Manuals