LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 159 (Engine Mechanical System (2GR-FKS) - Service Information (3 Of 3)) >> Engine Unit >> Removal [08/2021 - 09/2022] >> Procedure

Removal [08/2021 - 09/2022]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE KNOCK CONTROL SENSOR 

    Refer to REMOVAL [08/2021 - 09/2022]

  2. REMOVE SENSOR WIRE 
    1. Disengage the 2 clamps and remove the bolt and sensor wire.
      GTY665987Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  4. REMOVE VACUUM PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 5

  5. REMOVE NO. 3 WATER BY-PASS HOSE 
    1. Slide the clip and remove the No. 3 water by-pass hose from the water inlet pipe.
      GTY766407Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE NO. 2 WATER BY-PASS HOSE 
    1. Slide the clip and remove the No. 2 water by-pass hose from the water outlet.
      GTY766406Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE VENTILATION HOSE 
    1. GTY665986Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Slide the clip and remove the ventilation hose from the PCV valve (ventilation valve sub-assembly).

  8. REMOVE NO. 2 VENTILATION HOSE 
    1. Slide the clip and remove the No. 2 ventilation hose from the cylinder head cover sub-assembly.
      GTY671738Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE V-RIBBED BELT 

    Refer to PROCEDURE - Step 3

  10. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 5

  11. REMOVE COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH 

    Refer to PROCEDURE - Step 6

  12. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET 
    1. GTY766102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the 2 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly.

  13. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  14. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 
    1. Remove the 2 bolts and V-ribbed belt tensioner assembly.
      GTY766546Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE WATER PUMP PULLEY 

    Refer to PROCEDURE - Step 4

  16. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE 
    1. Remove the engine oil level dipstick from the engine oil level dipstick guide.
    2. Remove the bolt and engine oil level dipstick guide from the camshaft housing sub-assembly LH and oil pan sub-assembly.
      GTY766101Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the engine oil level dipstick guide O-ring from the engine oil level dipstick guide.
      GTY766100Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE DRIVE SHAFT BEARING BRACKET 
    1. Remove the 3 bolts and drive shaft bearing bracket from the cylinder block sub-assembly.
      GTY756938Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE WIRE HARNESS CLAMP BRACKET 
    1. Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly LH.
      GTY766053Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly.
      GTY766055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE WATER FILLER BRACKET 
    1. Remove the 2 bolts and water filler bracket from the camshaft housing sub-assembly LH.
      GTY766054Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE ENGINE COVER BRACKET 
    1. Remove the bolt and engine cover bracket from the cylinder head cover sub-assembly LH.
      GTY766105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals