Installation [09/2015 - ]: Procedure

INSTALL DOOR SIDE AIRBAG SENSOR

Check that the engine switch is off.

Check that the cable is disconnected from the negative (-) battery terminal.

WARNING:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Incorrect

Correct

Insert the door side airbag sensor stopper into the door hole, engage the claw and install the door side airbag sensor to the front door panel with the nut.

Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTE:

If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the door side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the door side airbag sensor stopper is securely inserted into the door hole.
Keep the stud bolt and waterproof rubber seal free of foreign matter.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Stopper

Connect the connector to the door side airbag sensor.

White Housing Lock

Connection is completed

NOTE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.

Check that there is no looseness in the installed parts of the door side airbag sensor.

INSTALL FRONT DOOR SERVICE HOLE COVER
Refer to PROCEDURE - Step 34 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 34 [12/2017 - ]
INSTALL FRONT DOOR NO. 1 TRIM BRACKET
Refer to PROCEDURE - Step 35 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 35 [12/2017 - ]
INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Refer to PROCEDURE - Step 46 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 46 [12/2017 - ]
INSTALL FRONT DOOR NO. 1 STIFFENER CUSHION
Refer to PROCEDURE - Step 47 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 47 [12/2017 - ]
INSTALL COURTESY LIGHT ASSEMBLY
Refer to PROCEDURE - Step 2
INSTALL DOOR ARMREST COVER
Refer to PROCEDURE - Step 49 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 49 [12/2017 - ]
INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Refer to PROCEDURE - Step 50 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 50 [12/2017 - ]
INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Refer to PROCEDURE - Step 51 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 51 [12/2017 - ]
INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
Refer to PROCEDURE - Step 52 [09/2015 - 12/2017] , or refer to PROCEDURE - Step 52 [12/2017 - ]
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Refer to INITIALIZATION [09/2015 - 08/2016] , or refer to INITIALIZATION [08/2016 - 12/2017] , or refer to INITIALIZATION [12/2017 - 08/2019] , or refer to INITIALIZATION [08/2019 - ]
INSPECT POWER WINDOW OPERATION
Refer to OPERATION CHECK [09/2015 - ]
PERFORM DIAGNOSTIC SYSTEM CHECK
Refer to DTC CHECK / CLEAR [09/2015 - 08/2019] , or refer to DTC CHECK / CLEAR [08/2019 - ]
INSPECT SRS WARNING LIGHT
Refer to DIAGNOSIS SYSTEM [09/2015 - 08/2016] , or refer to DIAGNOSIS SYSTEM [08/2016 - 12/2017] , or refer to DIAGNOSIS SYSTEM [12/2017 - 08/2019] , or refer to OPERATION CHECK [08/2019 - ]