Removal [03/2017 - 05/2023]: Procedure

REMOVE FRONT SEAT ASSEMBLY LH
Refer to REMOVAL [03/2017 - 05/2023]
REMOVE FRONT SEAT ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.
REMOVE REAR SEAT ASSEMBLY
Refer to REMOVAL [03/2017 - ]
REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY
Refer to REMOVAL [03/2017 - 05/2023]
REMOVE NO. 1 CONSOLE BOX SUPPORT
Refer to PROCEDURE - Step 2 [03/2017 - 04/2020] , or refer to PROCEDURE - Step 2 [04/2020 - ]
REMOVE FRONT DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 10 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 10 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 10 [04/2020 - 05/2023]
REMOVE FRONT DOOR SCUFF PLATE RH
HINT:

Use the same procedure described for the LH side.
REMOVE FRONT DOOR OPENING TRIM COVER LH
Refer to PROCEDURE - Step 12 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 12 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 12 [04/2020 - 05/2023]
REMOVE FRONT DOOR OPENING TRIM COVER RH
HINT:

Use the same procedure described for the LH side.
REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH
Refer to PROCEDURE - Step 14 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 14 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 14 [04/2020 - 05/2023]
REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER RH
Refer to PROCEDURE - Step 15 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 15 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 15 [04/2020 - 05/2023]

REMOVE FRONT PILLAR GARNISH LH

Apply protective tape at the position shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Protective Tape

Place your hand at the position shown in the illustration and pull in the direction of the arrow shown in the illustration to detach the front pillar garnish clip and lift up the front pillar garnish LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Push in the release lever with your finger and remove the front pillar garnish clip from the vehicle.

NOTE:

If there is extreme damage to the front pillar garnish clip, replace it with a new one.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Release Lever
	Push

When the front pillar garnish clip cannot be detached by pressing the knobs with the fingers:

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Direction (A)
	Push

Lift up the front pillar garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Direction (B)
	Release Lever
	Push

Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the front pillar garnish clip with your fingers in the direction (B) to detach the front pillar garnish clip.

NOTE:

If there is extreme damage to the front pillar garnish clip, replace it with a new one.

Pull in the direction indicated by the arrow shown in the illustration to detach the clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove in this Direction

Pull the front pillar garnish LH in the direction of the arrow shown in the illustration to detach the guides and remove the front pillar garnish LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove in this Direction

Protect the curtain shield airbag assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Protective Cover
	Adhesive Tape

Cover the airbag with a cloth or piece of nylon and secure both ends of the cover with adhesive tape as shown in the illustration.
NOTE:
Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.

REMOVE FRONT PILLAR GARNISH RH
HINT:

Use the same procedure described for the LH side.
REMOVE OUTER LAP BELT ANCHOR COVER
HINT:

Use the same procedure for the opposite side.

Refer to PROCEDURE - Step 11
REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)
Refer to PROCEDURE - Step 12
REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)
HINT:

Use the same procedure described for the LH side.

REMOVE QUARTER INSIDE TRIM BOARD LH

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws and remove the quarter inside trim board LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

REMOVE QUARTER INSIDE TRIM BOARD RH
HINT:

Use the same procedure described for the LH side.
REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
Refer to PROCEDURE - Step 4
REMOVE REAR SEAT INNER BELT ASSEMBLY RH
HINT:

Use the same procedure described for the rear No. 1 seat inner belt assembly LH.

REMOVE QUARTER TRIM PANEL ASSEMBLY LH

Detach the clamp.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the 2 clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Place your hand at the position shown in the illustration and detach the hook.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Pull in the direction of the arrow shown in the illustration to detach the claws and clip.

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws and clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws in order.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction
	Order of Removal

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Place your hand at the position shown in the illustration and detach the clip to remove the quarter trim panel assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Disconnect the connector.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

REMOVE QUARTER TRIM PANEL ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

REMOVE CENTER PILLAR GARNISH ASSEMBLY LH

Remove the 2 clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the hooks.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Detach the claws.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove in this Direction

Detach the guide in the direction of the arrow shown in the illustration and remove the seat belt guide LH.
Pull out the seat belt guide LH and front seat outer belt assembly LH (floor anchor) from the center pillar garnish assembly LH and remove the center pillar garnish assembly LH.

REMOVE CENTER PILLAR GARNISH ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

REMOVE INNER ROOF SIDE GARNISH LH

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow and detach the claw and clips in order to remove the inner roof side garnish LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

REMOVE INNER ROOF SIDE GARNISH RH
HINT:

Use the same procedure described for the LH side.

REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and roof side trim garnish clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Place your hand at the position shown in the illustration and detach the clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Push in the release lever with your finger, detach the roof side trim garnish clip from the vehicle and remove the roof side rail garnish assembly LH.

NOTE:

If there is extreme damage to the roof side trim garnish clip, replace it with a new one.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Release Lever
	Push

When the roof side trim garnish clip cannot be detached by pressing the knobs with the fingers:

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Direction (A)
	Push

Lift up the roof side trim garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Direction (B)
	Release Lever
	Push

Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the roof side trim garnish clip with your fingers in the direction (B) to detach the roof side trim garnish clip.

NOTE:

If there is extreme damage to the roof side trim garnish clip, replace it with a new one.

REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the inner upper roof side garnish clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Remove in this Direction

Push in the release lever with your finger and remove the inner upper roof side garnish clips from the vehicle.

NOTE:

If there is extreme damage to the inner upper roof side garnish clip, replace it with a new one.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Release Lever
	Push

When the inner upper roof side garnish clip cannot be detached by pressing the knobs with the fingers:

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Direction (A)
	Push

Lift up the inner upper roof side garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Direction (B)
	Release Lever
	Push

Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the inner upper roof side garnish clip with your fingers in the direction (B) to detach the inner upper roof side garnish clip.

NOTE:

If there is extreme damage to the inner upper roof side garnish clip, replace it with a new one.

Pull in the direction of the arrow shown in the illustration to detach the guides to remove the inner roof side garnish assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove in this Direction

Protect curtain shield airbag assembly:

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Protective Cover
	Adhesive Tape

Cover the airbag with a cloth or piece of nylon and secure both ends of the cover with adhesive tape as shown in the illustration.
NOTE:
Cover the curtain shield airbag assembly with a protective cover as soon as the inner roof side garnish assembly LH is removed.

REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

REMOVE VISOR BRACKET COVER LH

Detach the claws and remove the visor bracket cover LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

REMOVE VISOR BRACKET COVER RH
HINT:

Use the same procedure described for the LH side.

REMOVE VISOR ASSEMBLY LH

Remove the 2 screws.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Pull in the direction of the arrow shown in the illustration (1) to detach the visor assembly LH from the visor holder LH.

	Remove in this Direction (1)
	Remove in this Direction (2)

Pull in the direction of the arrow shown in the illustration (2) and remove the visor assembly LH.
NOTE:
Do not twist or remove the visor assembly in any direction other than downwards as the connector may become damaged.

REMOVE VISOR ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.
REMOVE MAP LIGHT SUB-ASSEMBLY
Refer to REMOVAL [03/2017 - 05/2023]
REMOVE RAIN SENSOR COVER
Refer to PROCEDURE - Step 1

REMOVE VISOR HOLDER LH

Turn the visor holder LH end approximately 90° in direction (1) indicated by the arrow shown in the illustration, and pull it out in direction (2) indicated by the arrow.

*a	90°
	Remove in this Direction (1)
	Remove in this Direction (2)

Detach the claws and remove the visor holder LH.

REMOVE VISOR HOLDER RH
HINT:

Use the same procedure described for the LH side.

REMOVE ROOF HEADLINING ASSEMBLY

Disconnect the 2 connectors.

Front pillar LH part:

Remove the protective cover installed to the front pillar LH.

Disconnect the 2 connectors.

Using a clip remover, detach the clamps and disconnect the No. 1 roof wire.
Install the protective cover to the front pillar LH.

Remove the screw from the coat hook.

HINT:

Use the same procedure for the opposite side.

Place your hand at the position shown in the illustration and detach the claws.

	Place hand here
	Remove in this Direction

HINT:

Use the same procedure for the other side.

for Carbon Roof:

Place your hand at the position shown in the illustration and detach the fasteners.

	Place hand here
	Remove in this Direction

for Glass Roof:

Detach the fastener.

Remove in this Direction

Slide the roof headlining assembly toward the rear of the vehicle and detach the clips.

Remove in this Direction

HINT:

The 3 clips remain on the vehicle side.

Remove the roof headlining:

Move the roof headlining assembly as shown in the illustration and remove it from the passenger door without making contact with the body interior.

Remove in this Direction

NOTE:

Check that the corners of the roof headlining assembly are free of bending, twisting and other deformation and that none of the mounted parts are falling off.
Do not damage the roof headlining assembly and body interior.
2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.

Turn in the direction of the arrow shown in the illustration and remove the 3 clips from the vehicle.

Remove in this Direction

Remove the grommet from the vehicle.

HINT:

Use the same procedure for the RH side.

REMOVE ROOF SIDE RAIL GARNISH

Detach the clamps and remove the roof side rail garnish.

Remove in this Direction

HINT:

Use the same procedure for the opposite side.