LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 60 (Emission Control System (A25A-FXS) - Service Information) >> EGR Valve >> Installation [06/2018 - 08/2021] >> Procedure

Installation [06/2018 - 08/2021]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL EGR VALVE ASSEMBLY 

    HINT: 

    Perform "Inspection After Repair" after replacing the EGR valve assembly.

    Refer to INITIALIZATION [06/2018 - 07/2019] , or refer to INITIALIZATION [07/2019 - 08/2020] , or refer to INITIALIZATION [08/2020 - 08/2021]

    1. Using an 8 mm socket wrench, install the EGR valve assembly to the EGR valve bracket with the bolt.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

    2. Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing.
      GTY759336Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin
      *b Hole
    3. Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing with the bolt.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

    4. for EGR Valve Bracket Connection Type:
      1. Using the 8 mm socket wrench, connect the fuel pipe sub-assembly to the EGR valve bracket with the bolt.

        Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

    5. Connect the No. 4 water by-pass hose and No. 8 water by-pass hose to the EGR valve assembly and slide the 2 clips to secure them.
  2. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY 
    1. Install a new EGR inlet gasket to the intake manifold.
    2. Install a new EGR valve adapter gasket to the No. 1 EGR pipe sub-assembly.
    3. Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly to the intake manifold and EGR valve assembly with the 4 bolts.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

  3. CONNECT EGR COOLER ASSEMBLY 
    1. Install a new EGR valve gasket to the EGR valve assembly.
      GTY741636Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw
      NOTE:

      Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.

    2. Connect the EGR cooler assembly to the EGR valve assembly with the 2 bolts.

      Torque: 24 N.m (245 kgf/cm, 18 ft.lbf) 

  4. CONNECT ENGINE WIRE 
    1. Engage the 2 wire harness clamps to connect the engine wire.
    2. Install the bolt.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

    3. Connect the EGR valve assembly connector.
    4. GTY783813Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Fuel Vapor Feed Hose
      *2 No. 2 Fuel Vapor Feed Hose

      Engage the 3 hose clamps to connect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.

  5. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 46

  6. ADD ENGINE COOLANT (for Engine) 

    Refer to PROCEDURE - Step 2

  7. INSPECT FOR COOLANT LEAK (for Engine) 

    Refer to PROCEDURE - Step 1

  8. INSPECT FOR EXHAUST GAS LEAK 

    Refer to PROCEDURE - Step 9

  9. PERFORM INITIALIZATION 
    1. Perform "Inspection After Repair" after replacing the EGR valve assembly.

      Refer to INITIALIZATION [06/2018 - 07/2019] , or refer to INITIALIZATION [07/2019 - 08/2020] , or refer to INITIALIZATION [08/2020 - 08/2021]

scientia non olet · About LEMON Manuals