LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2018 >> RX 450hL >> Repair and Diagnosis >> Electrical >> Gauges >> Meter / Gauge System (Service Information) >> Combination Meter >> Removal [08/2019 - ] >> Procedure

Removal [08/2019 - ]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [08/2019 - ]

  2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS 

    Refer to PROCEDURE - Step 2

  3. REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 2

  4. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 4

  5. REMOVE REAR NO. 4 FLOOR BOARD (w/ Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 3

  6. REMOVE BATTERY SERVICE HOLE COVER (w/ Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 4

  7. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    w/o Rear No. 2 Seat:

    Refer to PROCEDURE - Step 4

    w/ Rear No. 2 Seat:

    Refer to PROCEDURE - Step 5

  8. REMOVE INSTRUMENT PANEL GARNISH LH 

    Refer to PROCEDURE - Step 4

  9. REMOVE FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 9

  10. REMOVE COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 3

  11. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 7

  12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 8

  13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9

  14. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 2

  15. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 3

  16. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT 

    Refer to PROCEDURE - Step 5

  17. REMOVE LOWER INSTRUMENT FINISH PANEL SUB 

    Refer to PROCEDURE - Step 10

  18. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Disengage the 2 claws and 4 clips to separate the instrument cluster finish panel sub-assembly.
      GTY681602Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 4 clips as shown in the illustration.
      GTY635621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Disengage the 3 clips as shown in the illustration.
      GTY632600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    4. Disconnect the connector to remove the instrument cluster finish panel sub-assembly.
  19. REMOVE COMBINATION METER ASSEMBLY 
    1. Remove the 4 screws.
      GTY653796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp.
    3. Disconnect each connector to remove the combination meter assembly.
scientia non olet · About LEMON Manuals