LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2018 >> LS 500h AWD >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Exterior Panels / Trim - Service Information (4 Of 4) >> Front Door Window Frame Moulding >> Removal [10/2017 - 09/2018] >> Procedure

Removal [10/2017 - 09/2018]: Procedure

  1. PRECAUTION 
    WARNING:

    Be sure to read precaution thoroughly before servicing.

    Refer to PRECAUTION [10/2017 - 10/2020]

    GTY824211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [10/2017 - 09/2019]

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 24

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 3

    WARNING:
    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    • If the airbag deploys for any reason, it may cause a serious accident.
    GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [10/2017 - 09/2018]

  4. REMOVE FRONT DOOR TRIM UPPER COVER LH 

    Refer to PROCEDURE - Step 4

  5. REMOVE FRONT DOOR ARMREST COVER LH 

    Refer to PROCEDURE - Step 5

  6. REMOVE FRONT DOOR NO. 2 ARMREST COVER LH 

    Refer to PROCEDURE - Step 6

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 7

  8. REMOVE FRONT DOOR TRIM COVER LH 

    Refer to PROCEDURE - Step 17

  9. REMOVE UPPER DOOR FRAME GARNISH LH 

    Refer to PROCEDURE - Step 18

  10. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 19

  11. REMOVE FRONT DOOR VENT SEAL LH 

    Refer to PROCEDURE - Step 20

  12. REMOVE FRONT DOOR SERVICE HOLE COVER LH 

    Refer to PROCEDURE - Step 23

  13. REMOVE FRONT DOOR NO. 3 WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 29

  14. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 30

  15. REMOVE FRONT DOOR BELT MOULDING LH 

    Refer to PROCEDURE - Step 11

  16. REMOVE FRONT DOOR REAR BELT MOULDING END COVER LH 

    Refer to PROCEDURE - Step 32

  17. REMOVE FRONT DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE) 
    1. GTY797252Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the 3 nuts.

    2. GTY825435Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape

      Put protective tape around the front door window frame moulding LH (center pillar side).

    3. GTY779541Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)

      Detach the clip and guide and remove the front door window frame moulding LH (center pillar side) as shown in the illustration.

  18. REMOVE FRONT PILLAR UPPER COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 34

  19. REMOVE FRONT DOOR GLASS RUN LH 

    Refer to PROCEDURE - Step 35

  20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 38

  21. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 39

  22. REMOVE FRONT DOOR REAR WINDOW FRAME LH 

    Refer to PROCEDURE - Step 41

  23. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH 
    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.
    2. Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Standard Measurement

      Area Measurement
      A 5.0 mm (0.197 in.)
      GTY572016Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Tape
      NOTE:

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.
      WARNING:

      Be careful of the drilled rivets, as they may be hot.

      NOTE:
      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
    5. Detach the clip and remove the front door upper window frame moulding LH from the door frame.
      GTY797261Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. REMOVE FRONT DOOR NO. 3 GLASS RUN LH 
    1. Remove the clip.
      GTY797258Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the guide.
    3. Detach the guide and remove the front door No. 3 glass run LH from the front door upper window frame moulding LH.
      GTY826226Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  25. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING LH 
    1. GTY797248Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the 2 clips and the front door front window frame moulding LH.

scientia non olet · About LEMON Manuals