LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2016 >> LX 570 >> Repair and Diagnosis >> Engine Mechanical >> Lubrication System >> Engine Lubrication System (Service Information) >> Engine Oil Cooler >> Installation [09/2015 - ] >> Procedure

Installation [09/2015 - ]: Procedure

  1. INSTALL OIL COOLER SPACER 
    1. Apply a light coat of engine oil to a new gasket.
      GTY603077Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the gasket to the oil cooler spacer.
    3. Install the oil cooler spacer to the oil filter bracket with the bolt.
      GTY571704Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

  2. INSTALL OIL COOLER ASSEMBLY 
    1. Apply a light coat of engine oil to 2 new O-rings.
      GTY571706Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 2 O-rings to the oil cooler.
    3. Install the oil cooler with the 5 nuts.
      GTY610800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

  3. INSTALL OIL FILTER BRACKET 
    1. Apply a light coat of engine oil to 2 new O-rings.
      GTY604897Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 2 O-rings to the timing chain cover.
    3. Install the oil filter bracket with the 2 nuts and 2 bolts.
      GTY604891Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 35 N*m (357 kgf*cm, 26 ft.*lbf) 

  4. INSTALL NO. 1 OIL COOLER BRACKET 
    1. Connect the ground wire to the cylinder block.
      GTY593094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the oil cooler bracket with the 2 nuts.

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

  5. INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY 
    1. Connect the 4 hoses.
      GTY611522Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the water by-pass hose with the 3 bolts.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

  6. CONNECT COOLER COMPRESSOR ASSEMBLY 

    See step  31

  7. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY 

    See step  1

  8. INSTALL OIL FILTER ELEMENT 

    See step  5 [09/2015 - 08/2020], or see step  5 [08/2020 - ]

  9. INSTALL FAN & GENERATOR V BELT 

    Refer to PROCEDURE - Step 1

  10. INSTALL V-BANK COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 69

  11. ADD ENGINE OIL 

    See step  6 [09/2015 - 08/2020], or see step  6 [08/2020 - ]

  12. ADD ENGINE COOLANT 

    Refer to PROCEDURE - Step 6

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Refer to INITIALIZATION [09/2015 - 08/2019] , or refer to INITIALIZATION [08/2019 - ] ).

  14. INSPECT FOR OIL LEAK 

    See step  7 [09/2015 - 08/2020], or see step  7 [08/2020 - ]

  15. INSPECT ENGINE OIL LEVEL 

    Refer to PROCEDURE - Step 2

  16. INSPECT FOR COOLANT LEAK 

    Refer to PROCEDURE - Step 1

  17. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19

  18. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 15

  19. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH 

    Refer to PROCEDURE - Step 16

  20. INSTALL UPPER RADIATOR SUPPORT SEAL 

    Refer to PROCEDURE - Step 14

scientia non olet · About LEMON Manuals