LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2014 >> IS 350 Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 82 (Battery / Charging System (8AR-FTS) - Service Information) >> Generator >> Removal [08/2015 - ] >> Procedure

Removal [08/2015 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2024 Lexus IS 300, 2023 Lexus IS 300, 2022 Lexus IS 300, 2021 Lexus IS 300, and 2020 Lexus IS 300. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [08/2015 - 10/2016] , or refer to PRECAUTION [10/2016 - 10/2017] , or refer to PRECAUTION [10/2017 - 09/2020] , or refer to PRECAUTION [09/2020 - ]

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [08/2015 - 10/2016] , or refer to INITIALIZATION [10/2016 - 10/2017] , or refer to INITIALIZATION [10/2017 - 09/2020] , or refer to INITIALIZATION [09/2020 - 11/2021] , or refer to INITIALIZATION [11/2021 - 09/2022] , or refer to INITIALIZATION [09/2022 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

  3. REMOVE COOL AIR INTAKE DUCT SEAL 

    Refer to PROCEDURE - Step 1 [04/2013 - 10/2016] , or refer to PROCEDURE - Step 1 [10/2016 - 09/2020] , or refer to PROCEDURE - Step 1 [09/2020 - ]

  4. REMOVE INLET NO. 1 AIR CLEANER 

    Refer to PROCEDURE - Step 4 [08/2015 - 10/2016] , or refer to PROCEDURE - Step 4 [10/2016 - 09/2020] , or refer to PROCEDURE - Step 4 [09/2020 - ]

  5. REMOVE AIR CLEANER ASSEMBLY WITH NO. 2 AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 23 [08/2015 - 10/2016] , or refer to PROCEDURE - Step 22 [10/2016 - 09/2020] , or refer to PROCEDURE - Step 22 [09/2020 - ]

  6. REMOVE V-RIBBED BELT 

    Refer to REMOVAL [08/2015 - ]

  7. REMOVE GENERATOR ASSEMBLY 
    1. Disengage the 2 wire harness clamps.
      GTY617789Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the terminal cap.
    3. Remove the nut and disconnect the wire harness from terminal B.
    4. Disconnect the generator assembly connector.
    5. Disengage the 4 wire harness clamps.
    6. Remove the 2 bolts and generator assembly.
      GTY673651Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the 3 bolts and 2 wire harness clamp brackets from the generator assembly.
      GTY627746Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals