Inspection Procedure

1. When the luggage compartment door opener main switch is ON (Pushed), push the luggage compartment door opener inner switch and check that the luggage compartment door opens

   OK: Luggage compartment door opener system operates normally. 

2. When the luggage compartment door opener main switch is OFF (Free), push the luggage compartment door opener inner switch and check that the luggage compartment door does not open

   OK: Luggage compartment door opener system does not operate. 

Fig 1: Identifying Luggage Compartment Door Opener Main Switch

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: Go to step 2 

OK: END 

1. Connect the Techstream to the DLC3
2. Turn the engine switch on (IG)
3. Turn the Techstream on
4. Enter the following menus. Body Electrical / Body / Active Test
5. Perform the Active Test according to the display on the Techstream.

   Body 

   ITEM RANGE REFERENCE
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Trunk and Back-Door Open	Operate luggage compartment door lock motor	ON/OFF	-

   OK: Luggage compartment door lock motor operates. 

NG: Go to step  4

OK: Go to next step 

1. Connect the Techstream to the DLC3
2. Turn the engine switch on (IG)
3. Turn the Techstream on
4. Enter the following menus: Body Electrical / Body / Data List.
5. Read the Data List according to the display on the Techstream.

   Body 

   ITEM RANGE REFERENCE
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Trunk/B Door Open SW	Luggage door opening inner switch/ON or OFF	ON Luggage compartment door opener inner switch is pressed OFF Luggage compartment door opener inner switch is not pressed	-
   Trunk Main SW	Luggage door opener main switch signal/ON or OFF	ON Luggage compartment door opener main switch is pushed ON Luggage compartment door opener main switch is not pushed	-

   OK: On the Techstream screen, each item changes between ON and OFF according to above chart. 

   Result 

   RESULT REFERENCE
   
   

   Result	Proceed to
   OK (Luggage compartment door opener main switch and Luggage compartment door opener inner switch)	A
   NG (Luggage compartment door opener Inner switch)	B
   NG (Luggage compartment door opener main switch)	C

B: Go to step  6

C: Go to step  8

A: REPLACE MAIN BODY ECU RH (COWL SIDE JUNCTION BLOCK RH) 

1. Remove the luggage compartment door lock (See REMOVAL ).
2. Move the door lock to the close (lock) position.
3. Apply battery voltage to the door lock motor and check operation of the door lock motor

   OK 

   SPECIFICATION CHART
   
   

   Measurement Condition	Specified Condition
   Battery positive (+) → Terminal 1 (B) Battery negative (-) → Terminal 2 (E)	Luggage compartment door lock motor open operation

Fig 2: Inspecting Luggage Compartment Door Lock
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE LUGGAGE COMPARTMENT DOOR LOCK  (See REMOVAL )

OK: Go to next step 

1. Disconnect the J74 ECU connector
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   Q42-1 (B) - J74-1 (TR+)	Always	Below 1 Ω
   Q42-1 (B) - Body ground	Always	10 kΩ or higher
   Q42-2 (E) - Body ground	Always	Below 1 Ω

Fig 3: Identifying Q42 And J74 ECU Connector
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE MAIN BODY ECU RH (COWL SIDE JUNCTION BLOCK RH) 

1. Remove the luggage compartment door opener inner switch (See REMOVAL  )
2. Measure the resistance according to the value(s) in the table below

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Switch Condition	Specified Condition
   5 - 6	Pushed (ON)	Below 1 Ω
   5 - 6	Not pushed (OFF)	10 kΩ or higher

Fig 4: Identifying Luggage Compartment Door Opener Inner Switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE LUGGAGE COMPARTMENT DOOR OPENER INNER SWITCH  (See REMOVAL  )

OK: Go to next step 

1. Disconnect the J75 ECU connectors.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Taster Connection	Condition	Specified Condition
   J14-6 - J75-3 (TKUL)	Always	Below 1 Ω
   J14-6 - Body ground	Always	10 kΩ or higher
   J14-5 - Body ground	Always	Below 1 Ω

Fig 5: Identifying J14 And J75 ECU Connectors
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE MAIN BODY ECU RH (COWL SIDE JUNCTION BLOCK RH) 

1. Remove the luggage compartment door opener main switch (See REMOVAL  )
2. Measure the resistance according to the value(s) in the table below

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Switch Condition	Specified Condition
   1 - 2	Not pushed (OFF)	10 kΩ or higher
   1 - 2	Pushed (ON)	Below 1 Ω

Fig 6: Identifying Luggage Compartment Door Opener Main Switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE LUGGAGE COMPARTMENT DOOR OPENER MAIN SWITCH  (See REMOVAL  )

OK: Go to next step 

1. Disconnect the J75 ECU connectors
2. Measure the resistance according to the value(s) in the table below

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   J57-2 - J75-2 (TSW)	Always	Below 1 Ω
   J57-2 - Body ground	Always	10 kΩ or higher
   J57-1 - Body ground	Always	Below 1 Ω

Fig 7: Identifying J57 And J75 ECU Connectors
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE MAIN BODY ECU RH (COWL SIDE JUNCTION BLOCK RH)